Simplex DH Series RSG Door Holders, DH Model Series, 24 VDC, 24 VAC, and 120 VAC models

ULC CSFM Listed Approved door holders from RSG Reliable Group with four mounting types Semi flush wall mount for shallow box applications Surface wall mount with matching box Flush wall mount with recessed magnet for low profile Floor mount for single or double doors finish options High luster plating of chrome brass or dark bronze Powdercoated in chrome or dark bronze current multi voltage design reduces power and battery demands Models are available for operation with 24 VDC VAC or 120 VAC full wave rectifier allows AC or DC operation provides switching transient suppression Low residual magnetism allows easy door release for with low pressure door closers Rated holding force ranges from 20 lbs 9 kg to up to 110 lbs 49.8 kg and easy installation Self adjusting swivel catch plate adjusts to door changes Adhesive mounting templates assure alignment Required mounting hardware is supplied with each holder Magnet catch plates can be screwed to wooden doors drilled through and attached to a mounting bracket Floor mount door holders include drills and anchors mounting to concrete floors and hardware for to wooden floors Front plates provide convenient grounding screw accessories Extension rods are available in multiple lengths to proper alignment including a 4 102 mm long rod Drilling fixture for accurate repetitive installation listed to Standard 228 holders are normally energized to magnetically hold open In the event of a fire emergency the fire control panel or other compatible control means release the magnet allowing the door to close to the spread of smoke Doors may be manually or opened when the door holder is energized Alarm System Accessories RSG Electromagnetic Door Holders Mounted or Floor Mounted Reference Images without screw hole caps in place Wall Mount Door Holder Magnet Catch Plate Assembly Wall Mount Door Holder Magnet Supplied Box Mount Door Holder Magnet with Bracket and Box door model shown available for double doors These products have been approved by the California State Fire Marshal CSFM to Section 13144.1 of the California Health and Safety Code See CSFM Listing for allowable values and or conditions concerning material presented in document It is subject to re examination revision and possible cancellation listings may be applicable contact your local Simplex product supplier for the status Listings and approvals are under RSG Reliable Security Group 8 2012 Product Selection see specifications on page 4 and part number selection below Type Mount recessed Mount recessed magnet Mount ground Mount for door with single ground Mount for door with double Included Box Requirement assembly catch plate with bracket screw hole and required mounting hardware gang box 1 deep supplied separately assembly catch plate with bracket screw hole and required mounting hardware not shown on 1 refer to illustration on page 3 assembly catch plate with bracket screw hole matching electrical box and required mounting assembly with electrical box catch plate with floor mounting bracket screw hole caps and mounting hardware including drills and anchors for floors surface mount magnet assemblies with electrical box with electrical box two catch plates with brackets hole caps and required mounting hardware including and anchors for concrete floors gang box 2 deep supplied separately is supplied with door holder H x 2 W x 1 D mm x 70 mm x 54 mm Door Holder Accessories plate extender rod 1 25.4 mm long DHE1.5B Catch plate extender rod 1 38 mm long DHE4AB Catch plate with adjustable extender rod 4 102 mm long with center pivot plate extender rod 2 51 mm long plate extender rod 3 76 mm long extender includes two extension Fixture provides convenient alignment for repetitive installation Wrench for adding extender rod to catch plate two are needed two are shipped with each Door Holder Part Number Selection from each of the 6 categories to create part number see examples below Holder Operating Voltages For Style Type Color Mount Coils VDC VAC VDC VAC VDC VAC VAC VDC VAC VAC Mount luster Not floor DH24120RPC Door holder 24 VDC VAC or 120 VAC operation Recessed magnet flush mount Powdercoated Chrome finish DH24120GB2 Door holder 24 VDC VAC or 120 VAC operation Ground floor mount Brass finish high luster Double door DH1224SPC Door holder 12 or 24 VDC VAC operation Surface mount Powdercoated Chrome finish 8 2012 Semi Flush and Surface Mount Dimensions mm mm mm 1 1 2 mm mm mm mm mm mm mm and Surface Front View View Mount Side View entries are provided on and back of box Mount End View vertically or as needed Flush and Floor Mount Dimensions mm mm mm mm mm Mount Front View Mount View Door 76 mm Door 138 mm Mount Side View 8 2012 Catch Plate and Mounting Bracket Dimensions mm Plate mm holes mm mm mm side side swivel rod insert here Specifications Specifications Connections Plate Mounting Bracket mm mm mm mm die cast metal position terminal block with provisions for in out wiring common C low voltage high 22 to 12 AWG 0.5 to 3.31 mm2 DC AC Specifications and Performance High Holding Force High Holding Force V V V V VAC VAC V VAC mA mA mA mA mA additional information visit the RSG website http www rsgsecurity com mA mA mA mA mA mA mA mA L H L L H L L H lbs 13.6 kg lbs 34 kg lbs 18.1 kg lbs 15.8 kg lbs 49.8 kg lbs 9 kg lbs 9.8 kg SIMPLEX and the product names listed in this material are marks and or registered marks Unauthorized use is strictly prohibited 2012 Tyco Fire Protection Products All rights reserved All specifications and other information shown were current as of document revision date and are subject to change without notice Fire Protection Products Westminster MA 01441 0001 USA 8 2012