Simplex E-Series Heat Detectors for Extended Exposure to High Humidity

Listed FM Approved Initiating Peripherals E Series Electronic Heat Detectors for Exposure to High Humidity and reliable heat detection for of property listed to Standard 521 as a rate compensated detector temperature operation is suitable for most Thermistor based design is inherently rate due to minimal thermal lag Available for 135 F 57 C or 200 F 93 C UL spacing distance is 70 ft 21.3 m with rate of rise temperature detection Dual thermistor rate of rise operation For use where anticipated ambient temperature are less than 6 F minute 3.33 C minute UL spacing distance is 70 ft 21.3 m provides Epoxy encapsulated electronic detector design with plated contacts high humidity thermistor and steel screws Operation for ceiling or wall mounting Easily tested self restoring operation with repeatable Alarm indicating LED located on detector Current limited alarm that is compatible with two initiating device circuits IDCs Designed for EMI compatibility remote alarm indicating LED base options Bases for 2 wire or 4 wire operation Auxiliary relay output refer to selection chart on 2 for relay ratings Remote alarm indicating LED output Electronic Design Simplex electronic detectors use a fast response thermistor based design provide temperature sensing that quickly accurately consistently identifies when fixed temperatures are The fixed temperature sensing thermistor tracks the local ambient temperature This the time required to melt a lead pellet or heat a element as occurs in mechanical heat detector and provides the required heat detection for most This product was not ULC listed or approved by CSFM or MEA NYC or as of document date Additional listings may be applicable contact your local Simplex product for the latest status Listings and approvals under Simplex Time Recorder Co are property of Tyco Safety Products Westminster Electronic Heat Detector Mounted in Base Continued detection is determined by comparing thermistor responses By combining accurate with proper physical placement this patented detection design achieves a high level of not normally available with mechanical Operation Current Current 2 Wire Current 4 Wire to 32 VDC filtered DC with 30 ripple typical 100 maximum to 86 mA maximum exact current is by alarm current limiting of IDC mA typical 24 VDC FM requirements for operation 15 and 25 F min 8.33 and C min to diagram on page 3 for covered outdoor applications Operating the ambient conditions stated below to 95 RH from 32 to 122 F Range to 50 C Temperature Operating Range F Models F Models WARNING In most fires hazardous levels of smoke toxic gas can build up before a heat detection would initiate an alarm In cases where Life is a factor the use of smoke detection is highly to 100 F 0 to 38 C to 150 F 0 to 66 C 2 2015 Applications Reference detectors are used where property protection is and where life safety protection is not required or performed by other equipment Typical heat detector are satisfied by use of these fixed electronic detectors addition of rate of rise operation provides two forms heat detection for use where temperature fluctuations controlled and are less than 6 F min 3.33 C min temperatures may fluctuate more quickly use temperature detection to NFPA 72 the National Fire Alarm Code and 574 709 4098 Detectors Sensors and Bases Manual for additional guidance in applying locating heat detectors Products electronic heat detectors are similar to standard indoor electronic heat detectors but are equipped gold plated contacts a high humidity thermistor and steel screws For indoor heat detector refer to data sheet S4098 0014 Heat Detector Selection Chart compatible with bases listed below Alarm Indicating LED Operation heat detector LED turns ON continuously when in During normal conditions the LED is OFF Temperature Guidelines F 57 C fixed temperature detectors are for temperatures that do not exceed 100 F 38 C F 93 C fixed temperature detectors are for temperatures that exceed 100 F 38 C but are than 150 F 66 C Verification Application Note connecting these electronic heat detectors to a initiating device circuit IDC that is providing Verification for smoke detectors use the 4 wire base The 4 wire base provides an contact that is not current limited Heat detectors the 2 wire base present a current limited alarm that is not compatible with Alarm Verification devices other than smoke detectors are required activate the alarm without starting the alarm cycle at F 57 C F 93 C F 57 C F 93 C Operation applicable 15 25 F min 13.88 C min ft x 20 ft m x 6.1 m ft x 20 ft m x 6.1 m ft x 50 ft m x 15 2 m Ratings Spacing Time Index ULC Spacing ft x 70 ft m x 21.3 m Heat Detector Base Selection Chart Base no options Base with for remote alarm indicator Base with alarm relay Must be as the only on the IDC to relay operation Base with alarm relay Requires 24 VDC power connections connections connections Operation Type Type connections terminals for in out wiring 18 to 14 AWG terminals for 18 to 14 AWG for in out wiring of zone coded 18 AWG leads for in out wiring of zone coded 18 AWG leads Ratings A 28 VDC A 120 AC Form contacts for suppressed Connections terminals for 18 to 14 AWG for in out wiring of zone coded 18 AWG leads for in out wiring of zone connections Color coded 18 AWG leads Operation Type Ratings limited A 28 VDC A 120 AC Form contacts for suppressed Connections coded 18 AWG leads for in out wiring Type connections connections Color coded 18 AWG leads connections Screw terminals for 18 to 14 AWG for in out wiring of power coded 18 AWG leads for in out wiring of power Fast wire equivalents 18 AWG 0.82 mm2 14 AWG 2.08 mm2 2 2015 Heat Detector Accessories Plate Compatibility for surface or semi flush mounting to 4 102 mm square box or for surface mounting to 4 octagonal box also be used when retrofitting to replace existing larger diameter Red LED Indicator on single gang stainless steel plate wiring connections are AWG color coded leads only Relay Epoxy encapsulated design 24 VDC operation wiring connections 18 AWG color coded leads Relay Mounted on single gang stainless steel plate 24 VDC operation connections are 18 AWG color coded leads 4 wire IDCs 4098 9682E one per wire equivalent