Simplex Installation 4100-6048 VESDA Interface Card

Introduction Interface Cards Instructions publication describes the installation procedure for the 4100 4120 0154 and 4100 6048 Interface modules document covers the following topics Configuring wiring and installing a VESDA RS 232 Interface card in a 4100 4100U FACP Adding supervisory wiring to a VESDA power supply This wiring is only required for power supplies and is not required if VESDA detectors are powered by 4100 power Laser Focus Product Guide This document ships with the Laser Focus It gives instructions installing wiring and powering up the detector Laser Compact Product Guide This document ships with the Laser Compact It gives on installing wiring and powering up the detector Sheet for VESDA LaserPlus and VESDALaserScanner This document ships with Laser Plus and the Laser Scanner It gives instructions on installing wiring and powering the detector Reference Document LCD Programmer Product Guide This document is available on the web site and documents how to program using the LCD Programmer The same is used with the HLI Field Wiring Diagram for 4100 Power Limited 841 731 or Field Wiring Diagram for Non Power Limited 841 995 Fire Alarm System Installation Guide 574 848 Page and Warnings Jumpers Switches the Motherboard into 2975 91xx Back Boxes 4100 Motherboards into 2975 94xx Back Boxes the Daughter Card a Power Supervision Circuit for VESDA Power Supplies this Publication publication discusses the following topics 2005 2011 SimplexGrinnell LP All rights reserved and other information shown were current as of publication and are subject to change without notice and the Simplex logo are trademarks of Tyco International Ltd and its affiliates and are used under license J and Warnings and AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depend upon proper installation NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify an authorized product supplier HAZARD Disconnect electrical field power when making any internal adjust or repairs All repairs should be performed by a representative or authorized agent of local Simplex product supplier HAZARD Static electricity can damage components Handle as follows yourself before opening or installing components to installation keep components wrapped in anti static material at all times RULES AND REGULATIONS PART 15 This equipment has been tested and to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC These limits are designed to provide reasonable protection against harmful when the equipment is operated in a commercial environment This equipment uses and can radiate radio frequency energy and if not installed and used in with the instruction manual may cause harmful interference to radio Operation of this equipment in a residential area is likely to cause harmful in which case the user will be required to correct the interference at his own Jumpers Jumper jumpers on the VESDA RS 232 interface daughter card are factory preset and should not modification If necessary use this section to verify that the jumpers are in the correct See Table 1 and Figure 1 1 VESDA Default Jumper Settings the table above 2 3 means you should place the jumper on pins 2 and 3 whereas a designation 1 2 means you should place the jumper on pins 1 and 2 s s 1 Jumper Settings for VESDA RS 232 Interface Card Switches SW1 on the VESDA RS 232 interface daughter card is a bank of eight dip switches From to right see Figure 2 these switches are designated as SW1 1 through SW1 8 The function these switches is as follows SW1 1 This switch sets the baud rate for the serial communication line running between the RS 232 interface card and the 4100 CPU Set this switch to ON SW1 2 through SW1 8 These switches set the card address within the 4100 FACP switches must be set to the value assigned to the card by the Programmer Refer to 1 for a complete list of the switch settings for all of the possible card addresses Move switch to the down position to turn it ON or to the up position to turn it OFF Switches 1 2 through 1 8 the Card Address Figure an Address of 3 Refer Table 1 for switch settings FD4 050 01 Rate SW 1 1 Be Set to 2 Jumper Settings for the VESDA RS 232 Interface Card on next page Switches Continued 2 4100 Daughter Card Addresses 1 2 1 3 1 4 1 5 1 6 1 7 1 2 1 7 1 8