Simplex Installation Instructions Audio Input Card

Audio Input Card Instructions this Publication publication describes the installation procedure for the 4100 1240 Audio Input Card card is compatible with 4100U and 4100ES Fire Alarm Control Panels Page Warnings and Regulatory Information Audio Input Card Input Card Specifications the Audio Input Card the Audio Input Card into an Expansion Bay 2001 2005 2006 2011 SimplexGrinnell LP All rights reserved and other information shown were current as of publication and are subject to change without notice and the Simplex logo are trademarks of Tyco International Ltd and its affiliates and are used under license E Warnings and Regulatory Information and AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depend upon proper installation NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify an authorized product supplier HAZARD Disconnect electrical field power when making any internal adjust or repairs All repairs should be performed by a representative or authorized agent of local Simplex product supplier HAZARD Static electricity can damage components Handle as follows yourself before opening or installing components to installation keep components wrapped in anti static material at all times The Audio Input Card 4100 1240 Audio Input Card is an adjunct card to both versions of the audio controller card provides the audio controller with the following Four additional input channels for live audio analog signals Two sets of four analog multiplexers for selection between any one of the card four inputs to two of these four signals can be routed from the input card to the controller at any time audio input card does not have any on board intelligence but instead is controlled by the controller card Up to two audio input cards can be controlled by the audio controller card Input Card 1 below is an illustration of the audio input card CONTROLLER PORT P11 3 MIC TROUBLE LED1 4 MIC TROUBLE LED2 INPUT JUMPERS INPUT TERMINAL TB1 LEDs 1 and 2 light to indicate a on the microphone circuit INPUT 1 The Audio Input Card Input Card Specifications audio input card receives both 5 V and 24 V power from the audio controller card following specifications apply to analog and digital audio controllers voltage 19 to 33 VDC at 10 mA max supervisory current 50 mA with mic active Operating Range F to 120 F 0 to 49 C F 32 C at 10 to 93 Relative Humidity non condensing the Audio Input Card P1 through P10 are used to configure the input levels and or input type for each of the audio inputs Default settings have all jumpers set to positions 1 2 which configure the card follows to Table 2 below to change any of the jumper settings Refer to Figure 1 for the location of jumper 1 and 2 set for 70 VRMS 3 and 4 set for Line level inputs All jumpers set for 1 2 1 Audio Input Jumpers Input 1 Input 2 Input 3 5 6 9 Input 4 7 8 10 N A indicates that the input voltage level or input type shown is not supported by that The jumpers for inputs 3 and 4 should be treated as sets For example P3 5 6 and should always be in the same position as each other P4 7 8 and 10 also act as a VRMS VRMS VRMS Level the Audio Input Card into an Expansion Bay audio input card is designed to be mounted on the PDI in an expansion bay The card should mounted to the immediate right of the audio controller card If there are two audio input cards them to the two PDI connectors to the immediate right of the audio controller SCREWS INPUT CARDS 2 Mounting onto the Power Distribution Interface Card Connections to the Controller section describes how the audio controller card should be connected via a harness to the controller Refer to Fire Alarm System Digital Analog Audio Controller Installation 579 159 for field wiring audio input card must connect to the audio controller using the 734 048 Harness the harness from P11 on the audio input card to one of two inputs on the audio controller on which is free P9 or P10 on the analog audio controller P6 or P4 on the digital audio controller Input Card Input Card Audio Controller Audio Controller Input Card Input Card 3 Connecting to the Audio Controller Option Card audio input card is missing from either slot 1 or slot 2 next to the audio controller or is present slot 1 or 2 was configured not to have an audio input card microphone was configured for the option card but has a wiring fault open or short or is not E