Simplex Installation Instructions Comm & Audio Interface Modules

Introduction this Publication and Interface Modules Instructions publication describes the installation procedure for Transponder Interface Cards TICs Riser Modules and the Network Audio Riser Controller Module for installation in 4100U 4100ES Fire Alarm Control Panels product is compatible with 4100U and 4100ES Fire Alarm Control Panels FACP publication also includes connections that provide the Non Alarm Audio NAA Interface Verify FACP System Programmer Executive and Slave Software when installing or replacing system components Refer to Technical Support Information and Downloads website for compatibility Page and Warnings and Audio Riser Modules Guidelines Audio Riser Controller Module Audio Riser Module 566 407 833 Audio NAA Interface Replacement of the Digital Audio Riser Module 566 243 Audio PDI Termination Plug 2005 2011 SimplexGrinnell LP All rights reserved and other information shown were current as of publication and are subject to change without notice and the Simplex logo are trademarks of Tyco International Ltd and its affiliates and are used under license P and Warnings and AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depend upon proper installation NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify an authorized product supplier HAZARD Disconnect electrical field power when making any internal adjust or repairs All repairs should be performed by a representative or authorized agent of local Simplex product supplier SAFETY HAZARD Under certain fiber optic application conditions the optical output this device may exceed eye safety limits Do not use magnification such as a microscope other focusing equipment when viewing the output of this device HAZARD Static electricity can damage components Handle as follows yourself before opening or installing components to installation keep components wrapped in anti static material at all times RULES AND REGULATIONS PART 15 This equipment has been tested and to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC These limits are designed to provide reasonable protection against harmful when the equipment is operated in a commercial environment This equipment uses and can radiate radio frequency energy and if not installed and used in with the instruction manual may cause harmful interference to radio Operation of this equipment in a residential area is likely to cause harmful in which case the user will be required to correct the interference at his own REACCEPTANCE TEST AFTER SOFTWARE CHANGES To ensure system operation this product must be tested in accordance with NFPA 72 after any operation or change in site specific software Reacceptance testing is required any change addition or deletion of system components or after any modification repair adjustment to system hardware or wiring components circuits system operations or software functions known to be affected by a must be 100 tested In addition to ensure that other operations are not affected at least 10 of initiating devices that are not directly affected by the up to a maximum of 50 devices must also be tested and proper system operation 72 is a registered trademark of the National Fire Protection Association and Audio Riser Modules List 1 TIC Audio Riser and Riser Controller PIDS following TICs audio risers and audio riser controller modules are available for a Fire Alarm Control Panel FACP as well as for a 4100U 4100ES MINIPLEX Basic Transponder Interface Card TIC Module Local Mode TIC Module Analog Audio Riser Module Digital Audio Riser Module Network Audio Riser Controller Module Multiple Command Center Digital Audio Riser Module Interface Cards TICs receive data from the host panels allowing remote locations perform fire alarm functions TIC modules are optionally available with local mode operation provides basic degraded mode system functions in the event of a communication loss with master panel TICs receive communications from the host panel using Remote Interface RUI with either Style 4 or Style 7 wiring audio systems audio riser modules are required and are connected directly to TIC modules via cable Audio riser modules support Class A and Class B analog wiring as well as Style 4 Style 7 digital audio wiring Transponder Bay with PDI and Basic TIC Mode Transponder Bay with PDI and Local Mode TIC Transponder Interface Card TIC Audio Riser Module Audio Riser Module Digital Audio Riser Audio Riser Controller Module Mode TIC Block Utility Module Cabinet Tamper Switch Number Basic TIC basic TIC is an addressable device that contains an RUI input audio riser module interface a port for connecting to other transponder modules Local Mode TIC local mode TIC contains an RUI input audio riser module interface port for connecting to transponder modules and terminal block for connecting to an optional Local Mode Local Mode Controllers are mounted remotely from the transponder and are available red or beige flush or surface mount Model numbers are 4601 9108 9109 9110 9111 local mode controller is wired from the local mode TIC TB2 The outputs for the three switches three LEDs piezo sounder and power 24V 0V must be connect to the local controller on next page and Audio Riser Modules Continued Local Mode TIC local mode TIC acts as a controller for the transponder cabinet if the TIC loses communication the Master Controller When operating in local mode an alarm on any fire alarm input circuit cause all alarm notification appliance circuits to activate Relays and other auxiliary control will not activate The local mode controller is limited to alarm functions TIC MODE TIC GROUND FAULT ACTIVE RECEIVE RECEIVE RECEIVE ANALOG RISER 4100 0622 DIGITAL RISER 4100 1314 MCC OUT DIGITAL AUDIO RISER 1 2 1 OUT IN 1 TICs and Audio Riser Modules 2 Environmental Specifications Specifications all PIDs to 120 F 0 to 49 C to 93 relative humidity at 90 F 32 C on next page and Audio Riser Modules Continued LEDs module LEDs provide the following status information Illuminates to indicate communication loss with the host panel Illuminates when an RUI ground fault search is active Illuminates when Local Mode is active 4100 0625 Local Mode TIC only Illuminates to indicate an RUI Style 7 primary trouble Illuminates to indicate an RUI Style 7 secondary trouble Specifications 3 TIC 4100 0620 0625 Specifications Specifications voltage voltage Current VDC V 1 A 100 mV p p ripple mA maximum with no attachments no 8V load