Simplex Installation Instructions Digital Analog Audio Controllers

Introduction Audio Controllers Instructions Analog Audio Controller Board Digital Audio Controller Board Order for Field Replacement only Digital Audio Controller Board Constant Supervision publication describes the installation procedure for the following products are compatible with 4100U and 4100ES Fire Alarm Control Panels FACP Verify FACP System Programmer Executive and Slave Software when installing or replacing system components Refer to Technical Support Information and Downloads website for information this Publication publication discusses the following topics Page Warnings and Regulatory Information to the Audio Controllers Controller Card Specifications the Audio Controller Card the Audio Controller onto the PDI Controller Field Wiring the Digital Audio PDI Termination Plug 2001 2005 2006 2011 SimplexGrinnell LP All rights reserved and other information shown were current as of publication and are subject to change without notice and the Simplex logo are trademarks of Tyco International Ltd and its affiliates and are used under license G Warnings and Regulatory Information and AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depend upon proper installation NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify an authorized product supplier HAZARD Disconnect electrical field power when making any internal adjust or repairs All repairs should be performed by a representative or authorized agent of local Simplex product supplier SAFETY HAZARD Under certain fiber optic application conditions the optical output this device may exceed eye safety limits Do not use magnification such as a microscope other focusing equipment when viewing the output of this device HAZARD Static electricity can damage components Handle as follows yourself before opening or installing components to installation keep components wrapped in anti static material at all times RULES AND REGULATIONS PART 15 This equipment has been tested and found to with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules limits are designed to provide reasonable protection against harmful interference when equipment is operated in a commercial environment This equipment generates uses and radiate radio frequency energy and if not installed and used in accordance with the manual may cause harmful interference to radio communications Operation of equipment in a residential area is likely to cause harmful interference in which case the will be required to correct the interference at his own expense REACCEPTANCE TEST AFTER SOFTWARE CHANGES To ensure proper operation this product must be tested in accordance with NFPA 72 after any operation or change in site specific software Reacceptance testing is required any change addition or deletion of system components or after any modification repair adjustment to system hardware or wiring components circuits system operations or software functions known to be affected by a must be 100 tested In addition to ensure that other operations are not affected at least 10 of initiating devices that are not directly affected by the up to a maximum of 50 devices must also be tested and proper system operation 72 is a registered trademark of the National Fire Protection Association to the Audio Controllers 4100 1210 Analog Audio Controller 4100 1211 Digital Audio Controller 4100 1311 Digital Controller and their respective option cards make up the audio controller subsystem of the Alarm System The controller is the head end of the audio system and is seen by the system as a single slave only the audio card is visible while any option cards appear logically as locations on the audio controller main function of the audio controller card is to control system audio inputs and to recreate audio messages for distribution throughout the system Analog audio inputs to the system local and remote microphones and fire fighter phone option cards and can be expanded the use of the 4100 1240 Audio Input Option Card Pre recorded messages are stored on audio controller FLASH memory and can be expanded through the use of the 4100 Message Expansion Card both the analog and digital versions of the controller have the capability to recreate stored audio messages the cards differ in their method of distributing audio throughout the The 4100 1210 Analog Audio Controller uses analog risers for system distribution and allows channels on 2 wire pairs of digital message reproduction The 4100 1211 or 1311 Digital Audio Controller uses an RS 485 based digital means for system distribution There are up to 8 channels on a single wire of digital message reproduction on this card The 4100 1311 DAC is fully backward compatible with previous digital audio as long as you set Supervision Jumper P8 to Position 1 2 to silence and have installed 4100U Master Firmware Revision 11.08 or audio controller functionality includes supervision of its inputs and distribution risers and communication with the system CPU cards are compatible with either type of Audio Controller Card as are message files and software Functions Digital Audio Controller LED functions refer to Table 1 below to both Analog Digital 4100 1311 Only to Digital Controllers Only ENABLE When ON steadily indicates the audio controller is not communicating with the or is missing its slave exec code When OFF indicates that the controller is communicating with the master When FLASHING indicates the audio controller is downloading data from the download port When ON indicates the DAR is in degraded mode Class A is enabled When OFF indicates the DAR is not in degraded mode Class A is disabled When ON indicates that the DAR riser source is the DAR that coming from the SOURCE 4100 1311 Only to Digital Controllers Only 4100 1311 Only to Digital Controllers Only the 4100 1311 Digital Audio Controller replaces the 4100 1211 Digital Audio Controller LEDs 3 4 on the 4100 1311 should always be OFF In most LEDs 3 4 should both be ON or OFF at the same time only in rare circumstances would these LEDs be in different states such as when they user defined in custom control equations When OFF indicates the DAR riser source is this audio card DAR When ON indicates that this card is receiving the DAR from the PDI When OFF indicates that this card is driving its DAR onto the PDI DIRECTION on next page to the Audio Controllers Continued Controller 1 depicts the analog audio controller RISER TERMINAL TB1 CARD P2 RATE DIP SW1 CONNECTOR on side LOSS LED1 P8 P1 LED1 lights when the controller loses with the system CPU OPTION CARD 1 P9 OPTION CARD 2 P10 SPEAKER MIC P5 MIC TERMINAL TB2 on next page 1 The 4100 1210 Analog Audio Controller to the Audio Controllers Continued Controller 2 depicts the digital audio controller AUDIO RISER BLOCK TB2 P8 Only CARD P6 RATE DIP SW1 CONNECTOR P5 reverse side LOSS LED1 P7 P10 LED1 lights when the controller loses wi