Simplex Installation Instructions Expansion Signal Card

Introduction Signal XSIG Card Instructions publication describes the installation procedure for the Expansion Signal XSIG Card product is compatible with 4100U and 4100ES Fire Alarm Control Panels FACP Verify FACP System Programmer Executive and Slave Software when installing or replacing system components Refer to Technical Support Information and Downloads website for information this Publication publication discusses the following topics Page Warnings and Regulatory Information to the Expansion Signal Card the Expansion Signal Card onto the PDI Configuration 2005 2011 SimplexGrinnell LP All rights reserved and other information shown were current as of publication and are subject to change without notice and the Simplex logo are trademarks of Tyco International Ltd and its affiliates and are used under license E Warnings and Regulatory Information and AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depend upon proper installation NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify an authorized product supplier HAZARD Disconnect electrical field power when making any internal adjust or repairs All repairs should be performed by a representative or authorized agent of local Simplex product supplier SAFETY HAZARD Under certain fiber optic application conditions the optical output this device may exceed eye safety limits Do not use magnification such as a microscope other focusing equipment when viewing the output of this device HAZARD Static electricity can damage components Handle as follows yourself before opening or installing components to installation keep components wrapped in anti static material at all times RULES AND REGULATIONS PART 15 This equipment has been tested and found to with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules limits are designed to provide reasonable protection against harmful interference when equipment is operated in a commercial environment This equipment generates uses and radiate radio frequency energy and if not installed and used in accordance with the manual may cause harmful interference to radio communications Operation of equipment in a residential area is likely to cause harmful interference in which case the will be required to correct the interference at his own expense REACCEPTANCE TEST AFTER SOFTWARE CHANGES To ensure proper operation this product must be tested in accordance with NFPA 72 after any operation or change in site specific software Reacceptance testing is required any change addition or deletion of system components or after any modification repair adjustment to system hardware or wiring components circuits system operations or software functions known to be affected by a must be 100 tested In addition to ensure that other operations are not affected at least 10 of initiating devices that are not directly affected by the up to a maximum of 50 devices must also be tested and proper system operation 72 is a registered trademark of the National Fire Protection Association Introduction to the Expansion Signal Card Expansion Signal XSIG Card provides three additional NACs for use with either an Audio NAC or a power supply card SPS RPS and XPS When an XSIG Card is for audio NAC expansion the card is programmed for operation with the specific amplifier it is expanding XSIG card must be dedicated to provide either all Audio or all DC notification these cannot be mixed of the XSIG Card Provides three 1.5 A Class B NACs for Audio or DC notification Switches between two power audio input sources for example dual channel power stage switching Accepts Class A Adapter and Class B Expander for a total of six Class B NACs or Class A NACs per card that can be used with audio or DC signaling Accepts constant supervision audio NAC module for a total of three Constant NACs per card for use with audio signaling only When configured for use with non alarm audio quickly and automatically switches an audio source when a signal is detected at either input Supports earth fault isolation in conjunction with the source NAC supplying the card XSIG Card also supports the WALKTEST system test as long as the following programming are followed Custom Control must be written to turn on the NACs when the Group pseudo turns ON Lists can be created for the NACs to allow you to have them turn ON when different are activated However a Custom Control equation would be required for WALKTEST group equipment to accompany the XSIG card consists of the following Expansion Signal XSIG Card XNAC increases the quantity of Class B from three to six Expansion Signal XSIG Card Class A Adapter upgrades the three on NACs to Class A Expansion Signal XSIG Constant Supervision NAC replaces the on card with 3 Class A B Constant Supervision NACs on next page Equipment to the Expansion Signal Card Continued Signal Card 1 is an illustration of the Expansion Signal XSIG card B IN1 IN2 JUMPER FOR INPUT 1 P3 JUMPER INPUT 2 P4 2 THROUGH 8 TBL SWITCH SW1 CONNECTOR side 1 XSIG Card on next page to the Expansion Signal Card Continued Card Receives and PDI Card LEDs XSIG card is a 4100 Comm slave according to the 4100 slave architecture The card plugs the Power Distribution Interface PDI that supplies card power and 4100 Comm on the XSIG card are used to indicate card status See Table 1 1 Status LEDs No when the amplifier is not with the system CPU of audio NAC 1 routing relay status routed Input 2 audio use only of audio NAC 3 routing relay status routed Input 2 audio use only of audio NAC 2 routing relay status routed Input 2 audio use only Steadily during comm loss flashing during failure Steadily when NAC is ON Steadily when NAC detects trouble Steadily when NAC1 is routed to Input 2 Steadily when NAC is ON Steadily when NAC detects trouble Steadily when NAC2 is routed to Input 2 Steadily when NAC is ON Steadily when NAC detects trouble Steadily when NAC3 is routed to Input 2 is not provided on the XSIG card Limitations to Table 2 for electrical and environmental requirements 2 Electrical and Environmental Specifications VDC from FACP 19 32 VDC Specifications Requirements Current mA Specifications Use Use mA Power Supply or 100 W Amplifier mA Flex 35 or Flex 50 Amplifier A maximum A maximum 50 W OR 100 speakers whichever comes first Specifications to 120 F 0 to 49 C to 93 relative humidity at 90 F 32 C the Expansion Signal Card onto the PDI Expansion Signal XS