Simplex Peavey IRM 8150 Industrial Rackmount Mixer Amp

S P E C I F I C A T I O N S 8150 Amp All specifications are typical unless noted dBV 1 volt RMS dBu 778 volts RMS specs are referenced to nominal output 0 dBV unless otherwise noted measurements are wideband 20 Hz to 20 unless otherwise stated control settings are nominal 50 unless otherwise noted Input Noise dBV 40 dB max gain Response speaker outputs 1 dB 20 Hz to 20 kHz 1 kHz than 015 Impedance Z Bal 1.7 K ohms Input 13 K ohms EQ 12 dB 10 kHz minimum detent flat 2 dB EQ 12 dB 600 Hz minimum detent flat 2 dB EQ 12 dB 50 Hz minimum detent flat 2 dB Channel Gain Channel Gain Z 20 dB 0 dB Z 69 dB 89 dB Channel Gain Z 40 dB 20 dB Input Level Z 20 dBV 0 dBV Input Level Z 40 dBV 20 dBV Input Level Z 6 dB 26 dB Power V DC EQUALIZER Bandwidth octave Q Boost Cut 6 dB 12 dB dBV 1 kHz than 005 Response 1 dB 7 Hz to 40 kHz Level Frequencies ISO Stds Hz 125 Hz 250 Hz 1 kHz 2 kHz kHz 8 kHz 16 kHz Level 0 dBV 1.0 V RMS 19 dBV 9 V RMS Impedance K ohms Impedance ohms dB dB dB dB Output Level Headroom dB dB dB dB Impedance ohms ohms K ohms ohms Noise dBV 8.0 V RMS dBV 8.0 V RMS dBV 8.0 V RMS dBV 8.0 V RMS 100 dBV Master Level Down 94 dBV Master Nominal All Level Full CCW Aux Returns 86 dBV All Controls Nominal Z Input Terminated 150 ohms 0 dBV 1.0 V RMS 19 dBV 9 V RMS ACOUSTICS Input Impedance K ohms Input Level 0 dBV dBV dBV Input Level 4 dBV dBV dBV AMP SECTION Response 1 dB 20 Hz to 20 kHz Rated Power out 1 dB 50 Hz to 20 kHz Rated Power outputs Power Out 150 watts RMS 4 ohms Outputs 150 watts RMS 8 ohms 150 watts RMS 25 V 4 ohms 150 watts RMS 70 V 33 ohms 1 V RMS into 600 ohms Distortion than 0.1 10 mW to rated power Hz 7 kHz 4 ohms Harmonic Distortion than 0.1 Dynamic Range than 26 dB Maximum Distortion 0.5 THD for 6 dB overload 1 THD for 20 dB overload Noise dB below 150 watts Rate V m Sec Factor than 100 1 kHz 4 ohms Sensitivity V RMS for 150 watts 4 ohms Impedance K ohms Requirements watts 120 V AC 60 Hz The IRM 8150 features a rugged cold rolled steel and chassis finished in oven epoxy for toughness and screen utilizing the latest photographic and U V cured ink technology for hard wearing control I D calibration graphics Every on board component has carefully chosen to deliver the possible performance Preci professional reliability and minimal operating noise are only among the criteria used during the process of the components that ensure your IRM 8150 becomes an addition to your perfor equipment All printed circuit boards are from rugged U S military material using the latest auto assembly technology wave and computer controlled all Q A Each channel features front panel and monitor level controls as well high mid low equalization and AUX controls Every input channel has studio quality low impedance XLR WARRANTY input microphone input as well as 1 4 line input Switchable 48 V power is provided The unit features a 150 watt power The mixer shall have eight micro channels with both low and impedance inputs XLR and 1 4 Each channel shall have its own control as well as controls for high and low EQ Each channel shall have for sending to the Mon and AUX The master section shall include level controls for the Main Mon and Tape outputs as well as a nine band graphic equalizer standard frequencies with a metal cover The unit shall be packaged a rugged metal chassis 19 wide rack ears by 8 1 2 tall by 11 deep including external heatsinks rack mount The unit shall operate standard 120 volts AC 60 Hz power internal power amplifier shall be of delivering 150 watts RMS into ohms and 8 ohms as well as providing volt and 70 volt line outputs The unit be capable of delivering rated power 20 Hz to 20 kHz 1 dB into 4 ohms its direct output at 0.5 or less with hum and noise at least 80 below rated output from a line level The unit shall be called the Peavey Acoustics Division model 8150 Peavey Electronics Corporation warrants to the original purchaser of this new Architectural Acoustics product that it is free from in material and workmanship If within one 1 year from date of purchase a properly installed product proves to be defective and is notified Peavey will repair or replace it at no charge Note Batteries and patch cords not covered purchaser means customer for whom the product is originally installed Damage resulting from improper installation interconnection of a unit or system of another manufacturer accident or unreasonable neglect or any other cause not arising from defects in material and workmanship is not covered by this warranty The warranty is only as to products purchased and installed in the United States THIS LIMITED WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE IMPLIED OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE UNDER NO CIRCUMSTANCES WILL PEAVEY BE FOR ANY LOST PROFITS LOST SAVINGS INCIDENTAL DAMAGES OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE INABILITY TO USE THE PRODUCT EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE THIS LIMITED IS THE ONLY EXPRESSED WARRANTY ON THIS PRODUCT AND NO OTHER STATEMENT REPRESENTATION WAR OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY Peavey liability to the original purchaser for damages for any cause whatsoever and regardless of the form of action is limited to actual damages up to the greater of Five Hundred Dollars 500 or an amount equal to the purchase price of the product that caused damage or that is the subject of or is directly related to the cause of action This limitation of liability will not apply to claims for personal or damage to real property or tangible personal property allegedly caused by Peavey negligence For information on service this warranty call a Peavey customer service representative at 601 483 5376 ACOUSTICS and specifications subject to change without notice Division of Peavey Electronics Corporation 80302195 Printed in U S A 10 94 A Street Meridian MS 39301 U S A 601 483 5376 Telex 504115 Fax 486 1278