Simplex SX501 Non-Addressable Detector Base Sounder [INTERNATIONAL USE ONLY]

Detector Base Sounder Detector Base Sounder is a loop powered device that is controlled the detector plugged into it DIL switch sets the required tone and volume level Detector Base Sounder should not be used with detectors that a built in short circuit isolator for example the 850 series detec number Adaptor for Sounder VID VAD bases of the device Detector Base Base Sounder characteristics g material colour temperature temperature sounder shock corrosion protection to 70 to 70 to 95 non condensing SPL output quoted for 1000 mBar with EN54 3 series requirements A EN61000 6 3 output at 1 metre volume High volume Low volume volume dBA dBA dBA dBA loop voltage only Low Mid Low volume only High Mid High volume characteristics V 40 V 35 V Typical loading uA without detector fitted mA without detector fitted mA without detector fitted Not EN54 3 Base Sounder configuration sounder tone and volume are set by a DIL switch The DIL switch is accessible when the addressable detector is not fitted to the detector base Positions 1 to 4 set the required tone and positions 7 and 8 set the required volume level Position 6 is used to force the sounder on during but it remains off during normal operation version 1.0 Addressable Sensors with Isolator volume 1 Hz Sweep Slow Whoop 4 1 Hz Sweep Time Beep Hz Fast Sweep 3 Tone 970 operation ON test mode Volume Low Volume High Volume Volume switch setting positions 1 4 0 0 1 switch setting positions 6 8 0 0 0 0 1 X 1 0 X 1 1 X 0 0 X 0 1 X 1 0 X 1 1 X X X X X 0 0 0 1 1 0 1 1 1 Hz Sweep Slow Whoop 4 1 Hz Sweep Time Beep Hz Fast Sweep 3 Tone 970 1 Hz Slow 4 1 Hz Time Hz Fast 3 Tone Hz tone and description Hz description to 500 to 1200 over 1 s over 3.5 s 0.5 gap to 970 Hz ms On 500 ms Off to 970 ms ramp 7 Hz 880 ms per tone ms On 500 ms Off x 4 then 1 second gap ms On 500 ms Off x 3 then 1 second gap performance ceiling devices HIGH devices sound performance horizontal dBA at m devices sound performance vertical dBA 1 m 94 91 95 93 98 93 94 92 98 95 93 91 98 95 94 93 92 91 86 83 87 86 90 87 86 85 90 87 85 83 90 87 86 85 82 79 81 79 83 82 87 84 82 81 87 84 81 79 87 84 83 82 79 77 79 77 82 80 85 82 81 79 85 82 79 77 85 82 82 80 77 75 78 75 80 78 80 77 78 77 80 77 77 76 80 77 76 76 77 75 78 75 80 78 84 81 79 77 84 81 78 76 84 81 80 78 74 72 93 91 94 92 97 95 93 91 97 96 92 90 97 95 94 91 92 90 86 83 87 83 89 87 86 83 90 88 85 82 90 88 86 83 83 81 81 80 82 80 84 79 82 79 84 81 81 79 84 82 82 79 79 79 81 79 81 79 84 79 80 79 84 81 80 78 84 82 80 79 76 75 82 81 84 82 88 82 83 82 87 87 81 80 88 85 84 82 79 79 87 86 87 87 92 89 88 86 91 91 87 86 92 89 88 85 83 83 instructions Doc version 1.0 information units either fit directly to the ceiling or to an optional ceiling adaptor See Fig 1 Fig 2 for fitting the locking pin To remove a detector from a base with a locking pin these steps a suitable tool into the access hole to depress the locking pin in the detector Rotate the detector to remove units can be used with the Ceiling Tile Adapter CTA kit 517.050.060 by using CTA Adaptor Plate CTA AP 517.050.058 3 contains the dimensions of the Detector Sounder 1 Mounting the Detector Base Sounder 2 Fitting the locking pin 3 Detector Base Sounder dimensions Temporary park plunger Address flag holder Base Sounder cabling line in and out line in and out not be wired wired LED out wired only if a indicator is required Positive Positive Negative Negative Remote Indicator 4 Detector Base Sounder cabling notes All wiring must comply with local installation regulations and local fire system design requirements Ensure all conductors are free of earths Verify correct wiring and wiring polarity before connecting the devices to the addressable loop version 1.0 of Performance APPROVAL Addressable Sensors with Isolator required Declarations and certificates are publically available on the website www simplex fire com and are searchable by number or model name above fire detection products are components designed for use in Addressable Systems exclusively available to registered partners only They are intended for installation trained registered personnel only Systems should be installed and configured according to local regulations doc version 1.0 29 June 2018 2018 Johnson Controls All rights reserved All specifications and other information shown were current as of revision date and are subject to change without notice Fire Security GmbH Victor von Bruns Strasse 21 8212 Neuhausen am Rheinfall Switzerland