Simplex Synchronized Time Products, 6351 and 6400 Series Time Control Centers; also includes BCD Code Converter; (6400-0001)

AC line synchronous when 60 Hz powered or crystal Wall Mount Time Control Center Listed Certified model series 6351 and 6400 time centers provide Control of synchronous wired power line carrier and clock systems Simplex BCD binary coded decimal time selectable as either Standard BCD only or Extended BCD time and date Programmable daylight saving time correction Manual override switches for time controls 12 or 24 hour time display user selectable Easily programmed using the LCD time and status battery standby with 60 day backup for memory and timekeeping Four alternate program schedules with 1000 program available base Remote seconds synchronization input Surface semi flush wall mount or 19 rack mount Series Time Control Centers also provide Six programmable control circuits with manual Seven day programming with seconds resolution for Programmed times available to each circuit and each switches control features RS 232 interface for synchronization to an external time GPS receiver a computer using SIMSYNC or to another 6351 6400 Master Time Center clock control module Coded receiver interface Temperature compensated crystal oscillator TCXO Listed to Standard 863 Features Time Control Centers Model 6351 and 6400 provide accurate time keeping for secondary clocks including Simplex BCD time synchronous wired correction power carrier current correction and minute impulse clocks is also available for many non Simplex clock Refer to page 4 for additional information about BCD clock correction communications Listings and approvals under Simplex Time Recorder Co are the property of Tyco Safety Westminster Time Products and 6400 Series Control Centers 19 Rack Mounted Time Control Center Series Features Output Circuit Control In addition to clock 6400 Series products also provide six output with operation easily programmed for time and action and with individual manual control switches The LCD readout indicates the of each of the six circuits and when programming indicates time day of week and the selected Schedules Available Four independent can be easily programmed using the keypad can be selected singly or in multiples on system requirements Access Manual control switches and the are located behind a locked enclosure The keypad also be access code protected 8 2012 6400 and 6351 Display and Control Switches NORMAL RUN MODE indicates the time day of week circuit status and schedules In programming mode the display leads the user through programming sequence by flashing what is to be selected Responses to are entered via the keypad using either the or keys 6400 Time Only which are used for and in mode Series Time Shown for and mode 6351 SPRING and DST 6400 Time Only presence shown would that program is active CIRCUIT CONTROL 3 POSITION 6400 Series Time Only allows the programmed to occur ON and OFF the programmed control TIME CONTROL SWITCHES with red LED status AUTO allows the standard timing to occur MAN control and OFF override the standard operation GEN the motor of a carrier current motor generator SYNC the output of standard synchronous timing signals BCD only controls the output of the BCD timing signals 6400 and 6351 Programming Keypad 12 position programming keypad is used to set time date daylight saving time changes schedule changes selection of 12 hour or 24 hour display format entry may be secured by an access code which tampering or unauthorized program wall mounted time control centers the keypad is the locked door 8 2012 Clock Control and Coded Control Module Reference Clock Correction Module Clock Correction Compatibility following types of impulse clock systems can be Impulse Correction by the Impulse Clock Correction Module operates Simplex clocks or compatible is made using the module DIP switch clock systems and other correction see compatibility table is available for both 6400 6351 Series Time Control on selected models as a feature Not available aftermarket additions front controls include of Auto Manual or Off Two module front LEDs indicate the impulse as either Positive red or Negative polarity Impulse Correction Module connects to an internal module shown below and uses a multi tapped to provide the required operating voltage For impulse clocks it accumulates lost impulses a power failure and provides rapid correction to advance the impulse clocks to the correct time power is restored Type Minute Impulse Minute Impulse Minute Impulse Minute Dual Motor Minute Dual Motor Clocks 1 Minute Reverse 1 2 Minute Reverse Series Synchronous Impulse 12 Hour Correction 56th Minute 58th Minute Dual Motor Couch C452014 C452019 and C452133 C452145 and AR3A Impulse 60th 59th Minute Time Time Correction Control Output Module Coded Module Control Center Model includes a Coded module that a circuit of wired or line carrier current 6803 Series coded 6804 Series dual coded Output circuit number of the 6400 9003 is to coded relay and provides up to 10 control functions that single circuit The 10 on the front panel selection of the relay during programming and manual control Not for aftermarket additions Coded Impulse Correction Module Coded Dual Coded Control aftermarket installation in a Series Time Control Center mount or rack mount the module provides the of both the Impulse Correction Module and features of the Coded Dual Relay Control Module Impulse Control Output and required is included allows both features to be in the same control location Impulse and Coded 8 2012 TCXO Optional Time Control Modules TCXO Time Base Compensated Oscillator TCXO 6400 9504 is used for where power line frequency may be and unsuitable as a reference It is optionally for aftermarket in either a 6400 or 6351 Series Time Center This module a source of frequency to the central with accuracy of seconds per month from F to 122 F 0 C to 50 C RS 232 Interface Module Interface Module provides a link for to an external time including GPS computers using software or another using the 6400 9568 Converter see diagram page 5 It is optionally for aftermarket in either a 6400 or 6351 Series Time Center GPS connection to highly accurate time using a GPS refer to document GPS6400BRO1 for details on GPS 6400 GPS Time Reference Interface Module and Antenna Receiver GPS 427A computer connection install the 1603 9821 software package on a computer with an serial port that is connected to the 6400 9505 see sheet S1603 9821 for more information This allows to the computer time and if