Simplex Synchronized Time Products, Synchronous Clocks 6310 2310 Series A

cUL Listed Features Attractive modern SlimLine design Hour minute second hands and 16 round models Square Models automatic synchronization with correction Corrects Simplex 59 minute Time Rauland and various minute correction formats Microprocessor based movement Simple setup and installation Easily maintained and serviced Features Double Dial Round Brackets Double Dial Square Brackets Synchronous Clocks can be used in all types of from small offices to large scale industrial Round clocks are available in 12 and 16 sizes clocks are also available at 12 synchronous clock uses a stepped second hand and these capabilities correction Clocks are automatically with the Simplex Time Control Center hour This means clocks will display the correct time after less than 59 minutes of power failure that are up to 59 minutes slow or 55 seconds fast corrected completely on the hour correction Synchronization is provided for that are up to 12 hours slow This ensures that even most prolonged power interruption in individual or in the complete system will be compensated automatically Clocks that are up to 11 hours and 59 slow are corrected every 12 hours Time Products Clocks Series A Material Color or Light Gray Input side molded polycarbonate 130 VAC 50 60Hz 7 28 VDC VAC 24VAC Current mA 110VAC mA 24VDC VAC Tolerance hand minute hand second Range F to 120 F 0 C to 40 C non condensing size and type varies greatly depending on type voltage used quantity of clocks cable local codes and National Electrical Code Class I Your local Sales Representative is equipped assist you with complete clock system design services wiring specifications 3 21 Specifications Face ROUND V 60 Hz V 60 Hz ROUND V 60 Hz V 60 Hz ROUND V 60 Hz V 60 Hz 1 12 00 23 ROUND V 60 Hz V 60 Hz ROUND V 60 Hz V 60 Hz 1 12 00 23 ROUND V 60 Hz V 60 Hz ROUND V 60 Hz V 60 Hz ROUND V 60 Hz V 60 Hz SQUARE V 60 Hz V 60 Hz SQUARE V 60 Hz V 60 Hz 1 12 1 12 1 12 1 12 1 12 1 12 1 12 1 12 Dial Face S Symmetry D Designer 3 21 continued 2310A 6310A synchronous clocks may be used for service replacement of previously installed Simplex 2310 6310 clocks and for new synchronous wired system installation Replacement with clock Mount Clock Previously installed Simplex 2310 and 6310 surface mount synchronous clocks may have been using a 2310 9011 Receptacle Assembly as shown below replace these clocks with a Simplex 2310A or 6310A clock requires an A Simplex Cover Plate ordered separately Remove the connector from the existing 2310 9011 receptacle plate and insert it into A RETRO PLATE 1 Simplex Cover Plate Install a 6 32 x1 PH screw in the hole of the box Mount the clock onto the extended screw using the integral hole that is molded in the clock case as shown at right Mounting A previously installed 12 and 15 Simplex semi flush synchronous clock may have been mounted a 2975 9038 or 2975 9040 Back Box as shown below 2310 9802 12 and Clocks cm cm cm cm cm cm Round Semi Flush Square Semi Flush Round Semi Flush Square Semi Flush 3 21 replace these clocks with a Simplex 2310A or 6310A clock attach the clock mounting hanger and connector assembly to the 2310A 6310A replacement clock according to the instructions provided Attach the connector to the plug and hang the clock onto the back box Mounting 2310A and 6310A clocks are not compatible with existing Simplex 2310 9810 2310 9812 2310 9814 Double Brackets To double dial mount a Simplex 6310A round clocks requires installation of a 2 gang back box and either a Mount Housing for Slim Line 12 Round Analog Clock or Mount Housing for Slim Line 16 Round Analog Clock double dial mount Simplex 2310A square clocks requires installation of a 2 gang back box and either a for Double Flag Mount 8.5 Square Analog Clock Ceiling Mount Only or for Double Flag Mount 13.5 Square Analog Clock System Installation 2310A and 6310A synchronous clocks are ideal for installation in a new Simplex synchronous wired clock system Back Box 2310A 6310A synchronous clocks may be installed using either a 2310 9011 Receptacle Assembly and box or a 2975 9038 or 2975 9040 Back Box When a 2310 9011 Receptacle Assembly is utilized the terminal connector from the 2310 9011 receptacle plate and insert it into an A RETRO PLATE 1 Cover Plate ordered separately Double dial or flag mount requires installation of a 2 gang back box Install Molex Connector the four position Molex connector included to the clock according to the instructions provided with the clock Clock Mount Hanger mounting the clock to a 2975 9038 or 2975 9040 Back Box attach the clock hanger to the clock mounting the clock using a 2310 9011 Receptacle Assembly and one box the alternative locking assembly mount included may be used according to Simplex 2310A 6310A installation instructions 2310A and 6310A synchronous clocks may also be installed in non Simplex clock systems Protocol Detection microprocessor based movement of Simplex 2310A and 6310A synchronous clocks 59 minute correction and 58 minute correction protocols as well as National Rauland Midnight Reset and Dukane correction The clock will automatically and accept time correction from any of these protocols and requires less than five to perform hand position correction and the product names listed in this material are marks and or registered marks Westminster MA 01441 U S A use is strictly prohibited sheets may change without further notice 6 19 3 2021