Simplex TrueAlert Addressable Controller Programming Guide

TrueAlert Addressable Controller Guide B and Trademarks Simplex Time Recorder Co 2000 All rights reserved in the United States of America 2000 Simplex International Time Equipment Co Ltd Mississauga Ontario 1H3 Canada in this document is subject to change without notice No part of this document may be or transmitted in any form or by any means electronic or mechanical for any purpose the express written consent of Simplex Time Recorder Company and the Simplex logo are registered trademarks of Simplex Time Recorder Co following an eight digit Product ID number denotes ULC listed product TrueAlert and MAPNET II are trademarks of the Simplex Time Recorder Company in the United States of America and Warnings AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depends upon proper installation NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED Upon your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify Simplex HAZARD Disconnect electrical field power when making any internal or repairs Servicing should be performed by qualified Simplex Representatives HAZARD Static electricity can damage components Therefore handle as follows Ground yourself before opening or installing components use the 553 484 Static Control Kit Prior to installation keep components wrapped in anti static material at all times SAFETY HAZARD Under certain fiber optic application conditions the optical output of device may exceed eye safety limits Do not use magnification such as a microscope or other equipment when viewing the output of this device FREQUENCY ENERGY This equipment generates uses and can radiate radio energy and if not installed and used in accordance with the instruction manual may interference to radio communications It has been tested and found to comply with the limits a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules which are designed provide reasonable protection against such interference when operated in a commercial Operation of this equipment in a residential area may cause interference in which the user at his own expense will be required to take whatever measures may be required to the interference REACCEPTANCE TEST AFTER SOFTWARE CHANGES To ensure proper operation this product must be tested in accordance with NFPA72 1996 Chapter 7 after programming operation or change in site specific software Reacceptance testing is required any change addition or deletion of system components or after any modification repair or to system hardware or wiring components circuits system operations or site specific software functions known to be by the change shall be 100 tested In addition to ensure that other operations are not affected 10 of initiating devices that are not directly affected by the change up to maximum of 50 devices also shall be tested and proper system operation verified revised record of completion in accordance with 1 6.2.1 shall be prepared to reflect any of Contents 1 to the TrueAlert Addressable Controller 1 1 this Chapter 1 1 to TrueAlert 1 2 1 2 4009 TrueAlert Addressable Controller 1 3 1 3 Started 1 4 1 4 2 4010 Programming 2 1 PC Programming 2 2 Steps 2 2 Operation 2 5 Operation Custom Control 2 6 3 4100 4020 Programming 3 1 this Chapter 3 1 NACs 3 2 NACs 3 2 Programming 3 3 1 Specifying One or More 4009 TrueAlert Addressable Controllers 3 3 2 Defining TrueAlert Devices 3 7 3 Setting Class A and LED Options 3 10 4 Saving the Job 3 10 5 Checking Default Virtual NACs 3 11 6 Creating Custom Virtual NACs 3 13 the Configuration 3 15 Note About Custom Control 3 15 Next 3 15 I 1 of Figures 1 1 Simplex 4009 TrueAlert Addressable Controller 1 3 2 1 Card Tab Screen 2 2 2 2 Card Data Entry Screen 2 3 2 3 4009 Card Data Entry 2 4 2 4 System Options 2 5 2 5 Horn Custom Control 2 6 2 6 Horn Silence Custom Control 2 7 2 7 Custom Control for Visuals 2 8 3 1 Virtual NACs 3 2 3 2 System Configuration Menu 3 3 3 3 4020 Default Cards 3 3 3 4 Card Configuration Menu 3 4 3 5 List of Available Cards The Remote Interface Unit 3 4 3 6 Associating RUI and MAPNET Cards 3 5 3 7 4020 Interface List 3 6 3 8 4100 Interface List 3 6 3 9 Remote Unit Configuration Menu 3 7 3 10 Device Type List 3 8 3 11 Dev Address Field