Simplex TrueAlert Notification Appliances; Audible Visible Notification Appliances; Multi-Tone Horn Strobe with 520 Hz Output, Non-Addressable

ULC CSFM Listed Approved Notification Appliances Notification Appliances Multi Tone with 520 Hz Output Non Addressable Simplex 24 VDC multi tone multi candela provide Multi candela xenon strobe with synchronized 1 Hz flash jumper selected as 15 30 75 110 135 or 185 cd Per appliance tone selection of 520 Hz Horn Broadband Bell Chime High Low Slow Whoop or Siren using an on board DIP Switch refer to sound details on page 4 520 Hz tone is compliant with NFPA 72 Low Frequency Requirements for Sleeping Areas Operation is selectable for SmartSync two wire control free run operation Tone output level is selectable as high or low Diode polarized input for connection to reverse polarity Notification Appliance Circuits NACs Compatibility with ADA requirements refer to installation information on page 3 Electrical test point access without removing cover two wire control of audible and visible appliance provides Control of Horn Bell and High Low tones as Pattern March Time pattern or on controlled separately from visible on the same circuit Control of Slow Whoop Siren and Chime tones as continuous signals when receiving continuous commands SmartSync March Time pattern is selectable per to produce 60 BPM or 20 BPM Visible appliances on the same SmartSync circuit operate a synchronized 1 Hz flash rate Refer to page 2 for SmartSync control list and additional Strobe operation is listed to UL Standard 1971 and Horn operation is listed to UL Standard 464 and information Standard S526 Standard S525 design features include Rugged high impact flame retardant thermoplastic in red with white letters or white with red letters clear lens available with FIRE FEU ALERT or blank lettering Separate covers are available to change application type or for replacement covers can be easily removed disturbing the connected housing and avoiding conditions A separate mounting plate allows wiring to be completed appliance is mounted use with single gang double or 4 inch square box flush or surface mount wiring terminals for 18 AWG to 12 AWG Optional mounting adapters are available to cover mounted electrical boxes and to adapt to Simplex boxes Multi Tone A Vs are Available in Red with White and White with Red Lettering non addressable multi tone horn strobes provide a flexible of output tones and strobe intensity for fire audible notification Tone selection output level strobe intensity is set per appliance allowing needs to be tailored to specific area Refer to tone output details on page 4 Tone Selection DIP Switch selection the local tone choice A separate DIP Switch allows selection of a standard or a high output level selectable appropriate to the location See 4 for sound output ratings two stage alarm applications A DIP selection per appliance allows the SmartSync Time pattern input to be produced as 60 BPM or BPM The 20 BPM rate is typically required for two stage alarm applications as the pre signal by the Temporal Pattern Two stage alarm requires a 4010 4010ES 4100ES or 4100U as control panel mounting Multi tone horn strobes can be or surface mounted on a standard single gang gang or 4 square 102 mm electrical box accessories are available to increase mounting application flexibility This product has been approved by the California State Fire Marshal CSFM pursuant to 13144.1 of the California Health and Safety Code See CSFM Listing for allowable values and or conditions concerning material presented in document Additional listings may be applicable contact your local Simplex product for the latest status Listings and approvals under Simplex Time Recorder Co the property of Tyco Fire Protection Products 7 2016 Strobe Application Selection selection of visible notification is dependent on location local codes and proper applications the National Fire Alarm Code NFPA 72 ANSI the appropriate model building code BOCA or SBCCI and the application guidelines of the with Disabilities Act ADA Strobes Strobes When multiple strobes and their can be seen from one location synchronized reduce the probability of photo sensitive reactions well as the annoyance and possible distraction of flashing The multi candela strobes of these horn strobes are synchronized by the SmartSync operation NAC Product Selection SmartSync Two Wire Control operation mode allows a two wire circuit to the ability to activate both the multi tone horn strobe on the same NAC and then allow the multi horn to be silenced while the strobe remains flashing multi tone horn operates as while strobe operation is SmartSync Control Sources 4007ES Hybrid 4010ES 4100ES and 4100U Fire Control Panels refer to individual product data for more information 4009 IDNet NAC Extender refer to data sheet SmartSync Control Module SCM 4905 9938 refer data sheet S4905 0003 SmartSync compatible notification include separate multi tone horns and multi tone horn strobe notification appliances Multi Candela Horn Strobes Color Wording Description multi candela horn strobe for or Free run control includes cover matching mounting plate Select cover and mounting plate separately Mounting Plate Required when ordering model 49CMTV APPLW BA plate select color to match cover with Cover H x 5 W x 1 D mm x 127 mm x 38 mm Note BA indicates model is available either with or without the BA suffix Model numbers ending in BA APPLW models and mounting plates are assembled in the USA Covers Required when ordering model 49CMTV APPLW BA Adapters Only Only mount red adapter skirt mount white adapter skirt Adapter Plate red for mounting to Simplex 2975 9145 box for retrofit may be mounted vertical or horizontal to cover 1 1 2 deep mounted boxes Red mounting box requires Adapter Plate 4905 9931 Control Module SmartSync Control Module Class A or Class B installs in 4 square for use with control panels not providing SmartSync control H x 5 W x 1 D mm x 133 mm x 41 mm depth with horn 3 79 mm 5 x 5 x 0.060 Thick mm x 146 mm x 1.5 mm x 5 x 2 D mm x 130 mm x 70 mm x 4 x 1 D mm x 105 mm x 32 mm 7 2016 Installation Reference is compatible with single gang gang and 4 102 mm square boxes 38 mm deep supplied separately terminals and connection clips configuration switch from rear of not shown assembly cover when use flat bladed to release latch left side intensity slot on of appliance to scale test point access holes bottom Adapter Plate and Surface Mount Installation Reference Adapter Plate Box Mounting Reference Box WALL MOUNT