Simplex TrueAlert Notification Appliances; Multi-Tone Horns; SmartSync Controlled or Free-run; with 520 Hz output, Non-Addressable

TrueAlert Notification Appliances Horns SmartSync Controlled or Free run with 520 Hz output Non Addressable ULC CSFM Listed FM In out wiring terminals for 18 AWG to 12 AWG Optional mounting adapters are available to cover surface mounted boxes and to adapt to 2975 9145 boxes reference UL listed to Standard 464 ULC listed to Standard S525 non addressable multi tone horns a flexible selection of output tones for fire alarm audible Tone selection and output level is set for each appliance notification needs to be tailored to specific area requirements to Multi Tone Horn Specifications for details Tone Selection Switch selection determines the local tone choice A separate DIP position allows selection of a standard or a high output sound selectable appropriate to the location See Multi Tone Horn for sound output ratings mounting horns can be semi flush or surface mounted on a standard gang double gang or 4 in square 102 mm electrical box accessories are available to increase mounting and application Two Wire Control operation mode allows a two wire circuit to provide the ability activate both the horn and strobe on the same NAC and then allow horn to be silenced while the strobe remains flashing The horn as on until silenced while the strobe operation is on until Control Sources two wire control is available from Hybrid 4010ES 4100ES Fire Alarm Control Panels refer to product data sheets for more information IDNet NAC Extenders refer to data sheet S4009 0002 Control Module SCM Model 4905 9938 refer to data sheet 1 Multi Tone Horns are Available in with Red Lettering or Red with White Lettering 24 VDC multi tone horns provide Per appliance tone selection of 520 Hz Horn Broadband Horn Bell High Low Slow Whoop or Siren selected using an onboard DIP refer to sound output details on Multi Tone Horn Specifications details 520 Hz tone is compliant with NFPA 72 Low Frequency Signal for Sleeping Areas Listed for wall or ceiling mount applications blank covers are for ceiling mount applications Operation is selectable for SmartSync two wire control or free run Output level is selectable as high or low Diode polarized input for connection to reverse polarity supervised Appliance Circuits NACs Electrical test point access without removing cover two wire control of audible and visible notification provides Control of Horn Bell and High Low tones as Temporal Pattern March pattern or on continuously controlled separately from visible on the same circuit Control of Slow Whoop Siren and Chime tones as synchronized signals when receiving SmartSync continuous commands Visible appliances on the same SmartSync circuit operate at a 1 Hz flash rate Refer to SmartSync Two Wire Control for SmartSync control list and operation information design features include Rugged high impact flame retardant thermoplastic housing in red with letters or white with red letters available with FIRE FEU FEU FIRE blank lettering Separate covers are available to change application type on site or replacement covers can be easily removed without disturbing the housing and avoiding trouble conditions A separate mounting plate allows wiring to be completed before is mounted use with single gang double gang or 4 in box flush or surface mount This product has been approved by the California State Fire Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety Code See CSFM Listing 7135 0026 0379 for allowable and or conditions concerning material presented in this document Additional listings may be applicable contact your local product supplier for the latest status Rev 6 1 2020 Horns SmartSync Controlled or Free run with 520 Hz output Non Addressable Selection 1 Multi tone horns Model numbers ending in BA APPLW models and separate mounting plates are assembled in the USA horn for SmartSync or Free run includes cover and matching mounting cover and mounting plate separately with Cover 1 8 in H x 5 in W x 1 1 2 in D mm x 127 mm x 38 mm 2 Separate mounting plate required when ordering model 49CMT APPLW or 49CMT APPLW BA plate select color to match cover 3 Separate covers required when ordering model 49CMT APPLW or 49CMT APPLW BA White Red White 4 Mounting adapters Only mount red adapter skirt to cover 1 1 2 in deep surface mounted boxes mount white adapter skirt to cover 1 1 2 in deep surface mounted boxes Plate red for mounting to Simplex 2975 9145 box for retrofit may be mounted vertical or horizontal mounting box requires Adapter Plate 4905 9931 3 8 in H x 5 1 4 in W x 1 5 8 in D 136 mm x 133 mm x 41 mm depth with horn 3 1 8 in 79 mm 5 16 in H x 5 3 4 in W x 0.060 in D 211 mm x 146 mm x 1.5 mm 7 8 in H x 5 1 8 in W x 2 in D 200 mm x 130 mm x 70 mm Control Module Class A or Class B installs in 4 in box for use with control panels not providing SmartSync 5 Synchronization control module in H x 4 1 8 in W x 1 1 4 in D 102 mm x 105 mm x 32 mm 2 Rev 6 1 2020 Horns SmartSync Controlled or Free run with 520 Hz output Non Addressable Reference 2 Reference 3 Adapter Plate Installation Information Figure 3 shows 4905 9931 Adapter Plate 2975 9145 Box Surface Mount Side View Reference shows optional surface mount adapter skirt 1 in deep 4905 9937 Red 4905 9940 White conduit are provided on all four sides 3 Rev 6 1 2020 Horns SmartSync Controlled or Free run with 520 Hz output Non Addressable Horn Specifications Voltage Range Loading Range Range 6 Electrical specifications VDC to 33 VDC Special Application of 13 49CMT Series appliances for each NAC to 122 0 to 50 to 93 non condensing 104 40 blocks on mounting plate for 18 AWG to 12 AWG 0.82 mm2 to 3.31 mm2 two wires per terminal for wiring 7 Installation Instructions Instructions for 49CMT Series Horn for 49CMP Mounting Plates 8 Tone Characteristics Hz tone 600 3000 Hz signal Bell tone modulated tones with fundamentals of 1000 Hz and Hz 250 ms duration each 520 Hz to 1200 Hz sweep with 2 s duration 600 Hz to 1200 Hz to 600 Hz sweep with 2 s duration signal with a peak and decay time of 1 s compatible with control panel SmartSync for operation as Temporal Code 3 March or Continuous operation that operate as Continuous with with control panel SmartSync 9 TrueAlert Multi Tone Horn Current Ratings 16 VDC mA mA Multi Tone Horn Output Ratings 10 UL 464 Output Ratings 16 VDC and 33 VDC dBA High Low High tones are not used for coded operation Low Hz Horn Horn Whoop High 11 ULC S525 Output Ratings 16 VDC and 33 VDC dBA High tones are not used for coded operation Low