Symplex TrueAlert Addressable Notification Appliances, Multi-Candela Visible Only (V O) Amber Lens Strobes for Emergency Communications; S4906-0007

ULC CSFM Listed Addressable Notification Appliances Multi Candela Visible Only V O Amber Lens Ceiling Strobes for Emergency Communications Individually addressed and controlled V O visible only notification provide Amber lens with lettering produces a signal from clear lens fire alarm evacuation strobes for with Emergency Communications Systems Multi candela xenon strobe with synchronized 1 Hz rate and with intensity programmable from the panel or jumper selected as 15 30 75 or cd Advanced addressable notification controlled by IDNAC from Simplex 4100ES fire alarm control panels EPS EPS power supplies and 4009 IDNAC providing regulated 29 VRMS allowing to operate with lower current even under battery Separate device type allows connection on same SLC as lens strobes with independent operation clear for Fire Alarm amber strobes for Alert is clear Fire OR amber Alert not both Wiring supervision to each strobe allowing for Class B circuits to simplify wiring A circuits require in out wiring TrueAlert Device Reports at the control panel detailing point ID custom label type and candela see sample on page 3 Magnet test diagnostics to assist checkout and testing of and wiring Compatibility with ADA requirements refer to installation information on page 3 Compatibility with legacy TrueAlert addressable for upgrade and replacement see page 4 UL listed to Standard 1638 due to non white lens by UL testing to provide light dispersion of UL Standard 1971 at rated candela no necessary for amber lens ULC listed to Standard S526 indicator and magnet test feature Appliance LED can be selected to display each polling to indicate appliance supervision diagnostic mode the magnet test pulses the LED to appliance address AND pulses to indicate the selection a brief output of the strobe is also to confirm operation design features Rugged high impact flame retardant thermoplastic housing Rear of housing does not extend into box and easily to standard electrical boxes Options include box adapters and red wire guards Mount Addressable Amber Lens V Os Multi Candela TrueAlert addressable amber lens provide convenient installation to standard boxes The strobe is individually addressed and controlled with power supervision and supplied from a Simplex fire alarm control panel IDNAC Signaling Line Circuits SLCs See list on page 4 amber lens multi candela strobes provide non fire alert notification for use with Emergency systems where additional response is provided by audio or textual appliances Application Reference strobes used as part of an Emergency system are located to provide the same coverage as required of clear lens fire alarm strobes Emergency Communications requirements are in detail in document UFC 4 021 01 USA of Defense United Facilities Criteria and in 72 Chapter 24 2010 and 2013 editions strobe coverage criteria is further described in the Fire Alarm Code NFPA 72 ANSI A117.1 the model building code BOCA ICBO or SBCCI the application guidelines of the Americans with Act ADA See page 2 for wire guard listings This product has been approved by the California State Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety See CSFM Listing 7300 0026 325 for allowable values and or conditions material presented in this document FM approval and MEA acceptance are applicable Additional listings may be applicable contact your local Simplex product for the latest status Listings and approvals under Simplex Time Recorder Co are property of Tyco Fire Protection Products 8 2014 TrueAlert Addressable Diagnostics Features Controllers can be selected to pulse each LED when it receives a supervision poll When controller is selected for diagnostic mode the appliance test feature provides a response at the individual being tested Appliance Magnet Test In this test mode in to the magnet test the appliance LED pulses to conveniently indicate the appliance Appliance Testing In this test mode after address is indicated by pulsing the appliance LED the will briefly flash to indicate proper operation Instrument Two TSIT The 2nd generation the Simplex TrueStart Test Instrument adds testing of SLC wiring and TrueAlert and TrueAlert ES to its ability to test IDCs NACs and IDNet before connection to the control panel contact your local Simplex representative for information Addressable Wiring Isolator Model 4905 9929 is available for remote on TrueAlert addressable circuits to isolate circuited wiring from functioning wiring Refer to sheet S4905 0001 for additional information IDNAC SLC Operation Advantage V O Appliances with Addressable Strobes on IDNAC SLCs provide visible using a single two wire circuit that also connection to the individual notification electronic circuit This operation increases supervision integrity by providing supervision that beyond the appliance wiring connections current allows efficient IDNAC SLC With IDNAC SLCs a constant 29 VRMS voltage is maintained even during battery standby strobes to operate at higher voltage with lower and ensuring a consistent current draw and voltage margin under both primary power and secondary standby Efficiencies include wiring distances up 2 to 3 times farther than with conventional notification support for more appliances per IDNAC SLC or use of gauge wiring or combinations of these benefits providing installation and maintenance savings with assurance that appliances that operate during normal testing will operate during worst case alarm Installation and Testing Time With controls on the same two wire SLC installation and expense for both retrofit and new construction be significantly reduced When Class B wiring is wiring can be tapped allowing more savings in wire conduit size and utilization and overall efficiency Use of the magnet test feature installation efficiency TrueAlert device reports identify information about each connected Product Selection Addressable Strobe with Amber Lens Addressable Ceiling Mount Strobe white with red with amber lens intensity selectable as 15 30 75 or 110 x 2 5 x 2 D mm x 75 mm x 67 mm Adapter and Wire Guard Surface Mount Adapter Plate zinc plated required for ceiling surface boxes Ceiling Mount red wire guard with mounting plate compatible with or surface mounted boxes see diagram on page 3 x 4 x 2 mm x 111 mm x 73 mm x 3 124 mm x 79 mm UL listed by Space Age Electronics Inc TrueAlert Device Reports Reference Port 5 TrueAlert Device Report ID LABEL Label up to 40 characters Room 5 Room Fire Room Alert 1 MON 11 Aug 14 8 2014 Ceiling Mount V O and Guard Installation Reference gang box Wiremold V5744S 57 mm deep supplied by others setting DIPswitch is behind strobe select address and strobe setting before inserting into housing view location indicator box 1 1 2 38 mm deep RACO 650 or or single gang box 2 1 2 64 mm deep 519 or equal supplied by others can be attached to boxes mounted to drop T bar with clips ERICO No 512 or equal Adapter Plate required for surface with handy box unless using the 4905 9926 guard mount stro