Home » Solidyne sLON-WTSx Data Sheet
File preview
Click the button below to download immediately for free
Show text preview
TECH/DATA SHEET Temperature Sensors sLON-WTS Sensors are wall-mounted digital and humidity sensors for use with Controllers. These sensors feature Sensor Link communication protocol that provides a simple wire interface for power and exchange of sensor subbase information. Available in twelve models, sLON-WTS Sensors provide integral analog to conversion for elimination of electrical between sensor and controller. An wiring connection allows access to the network (LON via a LONWORKS network on the left side of each sensor. This jack allows connection to a PC running the WPT Software or a third party Network Management Tool. Each also provides an S-Link jack on the right side for to a PDA running Pocket sLON software. Sensors are suitable for direct-wall, 2 x 4 box, 1/4 DIN electrical box, or surface box Chart Table-1 on page 2 for a chart of the models. Corporation – www.solidyne.com rev1 04/2005 sLON-WTSx Model Chart. and Sensor only with override Sensor with setpoint adjustment and override Sensor with setpoint, override, and controller functions Sensor with setpoint, On/Off and Fan speed Sensor with setpoint, override, controller mode and emergency heat key displays value and setpoint. Allows viewing of alarms and diagnostics. displays values, setpoints, and controller mode functions. Override Status Indication LCDa and LED Override Status LCDc and LED Override Status LCDc and LED Fan Status LCDc, LED Override Status, and Heat Indication sLON-WTS Sensor is packaged disassembled in one box and consists of three major A pre-wirable base plate for wiring to the controller S-Link and LonWorks network (LON) An electronic assembly containing the sensors and associated circuitry A removable cover carton for damage. If damaged, notify carrier immediately. Inspect sensors for upon receipt. must be a qualified technician items not provided) Job wiring diagrams Tools: Drill and bits for mounting screws Level Static protection wrist strap Two mounting screws (dry-wall anchors for direct-wall mount) Disconnect power before installing or removing the cover. to observe this warning can damage the sensor. Follow Static Precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. rev1 04/2005 Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception
TECH/DATA SHEET Temperature Sensors sLON-WTS Sensors are wall-mounted digital and humidity sensors for use with Controllers. These sensors feature Sensor Link communication protocol that provides a simple wire interface for power and exchange of sensor subbase information. Available in twelve models, sLON-WTS Sensors provide integral analog to conversion for elimination of electrical between sensor and controller. An wiring connection allows access to the network (LON via a LONWORKS network on the left side of each sensor. This jack allows connection to a PC running the WPT Software or a third party Network Management Tool. Each also provides an S-Link jack on the right side for to a PDA running Pocket sLON software. Sensors are suitable for direct-wall, 2 x 4 box, 1/4 DIN electrical box, or surface box Chart Table-1 on page 2 for a chart of the models. Corporation – www.solidyne.com rev1 04/2005 sLON-WTSx Model Chart. and Sensor only with override Sensor with setpoint adjustment and override Sensor with setpoint, override, and controller functions Sensor with setpoint, On/Off and Fan speed Sensor with setpoint, override, controller mode and emergency heat key displays value and setpoint. Allows viewing of alarms and diagnostics. displays values, setpoints, and controller mode functions. Override Status Indication LCDa and LED Override Status LCDc and LED Override Status LCDc and LED Fan Status LCDc, LED Override Status, and Heat Indication sLON-WTS Sensor is packaged disassembled in one box and consists of three major A pre-wirable base plate for wiring to the controller S-Link and LonWorks network (LON) An electronic assembly containing the sensors and associated circuitry A removable cover carton for damage. If damaged, notify carrier immediately. Inspect sensors for upon receipt. must be a qualified technician items not provided) Job wiring diagrams Tools: Drill and bits for mounting screws Level Static protection wrist strap Two mounting screws (dry-wall anchors for direct-wall mount) Disconnect power before installing or removing the cover. to observe this warning can damage the sensor. Follow Static Precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. rev1 04/2005 Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception