Home » System Sensor MMF-300 Monitor Module Installation AND MAINTENANCE Instructions
File preview
Click the button below to download immediately for free
Show text preview
InstallatIon anD maIntenance InstructIons monitor module Operating Voltage: Current Draw: Operating Current: Resistance: IDC Resistance: IDC Voltage: IDC Current: Range: to 32 VDC (LED on) (group poll); 350 (direct poll); 600 Max. (Communicating, IDC Shorted) Ohms Ohms Volts to 120 (0 to 49 to 93% Non-condensing H x 4 W x 11/4 D (Mounts to a 4 square by 21/8 deep box.) Electrical Box FireLite Place CT 06472 203.484.7161 MMF-300 mounts directly to 4-inch square electrical boxes (see Figure 2). box must have a minimum depth of 21/8 inches. Surface mounted electri- boxes (SMB500) are available. 2. moDule mountIng: InstallIng information is included as a quick reference installation guide. Refer to control panel installation manual for detailed system information. If the will be installed in an existing operational system, inform the opera- and local authority that the system will be temporarily out of service. Dis- power to the control panel before installing the modules. This manual should be left with the owner/user of this equipment. DescrIptIon MMF-300 Monitor Module is intended for use in addressable, two-wire where the individual address of each module is selected using the rotary switches. It provides either a 2-wire or 4-wire fault tolerant Device Circuit (IDC) for normally open contact fire alarm or supervi- devices. The module has a panel controlled LED indicator. The MMF-300 be used to replace an M300 module in existing systems. requIrements ensure proper operation, these modules shall be connected to listed com- system control panels only. 1. controls anD InDIcators: All wiring must conform to applicable local codes, ordinances, and This module is intended for power limited wiring only. Install module wiring in accordance with the job drawings and appropri- wiring diagrams. Set the address on the module per job drawings. Secure module to electrical box (supplied by installer), as shown in 2. 3. typIcal 2-WIre InItIatIng DevIce cIrcuIt (IDc) confIguratIon, nfpa style B (class B): NEXT NUMBER OF UL LISTED CONTACT DEVICES MAY BE USED. DO MIX FIRE ALARM INTIATING, OR SECURITY DEVICES THE SAME MODULE. EOL DEVICE CIRCUIT (IDC) – NFPA STYLE B LIMITED: 450 MAX. @ 11 VDC MAX CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS. WIRING SHOWN IS SUPERVISED AND POWER LIMITED 4. typIcal 4-WIre fault tolerant InItIatIng DevIce cIrcuIt (IDc) confIguratIon, nfpa style D (class a): OR MODULES TO LISTED CONTROL PANELS ONLY LINE CIRCUIT (SLC) VDC MAX. PAIR RECOMENDED OR MODULES TO LISTED CONTROL PANELS ONLY LINE CIRCUIT (SLC) VDC MAX. PAIR RECOMENDED NEXT NUMBER OF UL LISTED CLOSURE DEVICES BE USED. DO NOT MIX FIRE INTIATING, SUPERVISORY, SECURITY DEVICES ON THE MODULE. RESISTOR INTERNAL TERMINALS & 9 CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS. WIRING SHOWN IS SUPERVISED AND POWER LIMITED FireLite Alarms Inc.
InstallatIon anD maIntenance InstructIons monitor module Operating Voltage: Current Draw: Operating Current: Resistance: IDC Resistance: IDC Voltage: IDC Current: Range: to 32 VDC (LED on) (group poll); 350 (direct poll); 600 Max. (Communicating, IDC Shorted) Ohms Ohms Volts to 120 (0 to 49 to 93% Non-condensing H x 4 W x 11/4 D (Mounts to a 4 square by 21/8 deep box.) Electrical Box FireLite Place CT 06472 203.484.7161 MMF-300 mounts directly to 4-inch square electrical boxes (see Figure 2). box must have a minimum depth of 21/8 inches. Surface mounted electri- boxes (SMB500) are available. 2. moDule mountIng: InstallIng information is included as a quick reference installation guide. Refer to control panel installation manual for detailed system information. If the will be installed in an existing operational system, inform the opera- and local authority that the system will be temporarily out of service. Dis- power to the control panel before installing the modules. This manual should be left with the owner/user of this equipment. DescrIptIon MMF-300 Monitor Module is intended for use in addressable, two-wire where the individual address of each module is selected using the rotary switches. It provides either a 2-wire or 4-wire fault tolerant Device Circuit (IDC) for normally open contact fire alarm or supervi- devices. The module has a panel controlled LED indicator. The MMF-300 be used to replace an M300 module in existing systems. requIrements ensure proper operation, these modules shall be connected to listed com- system control panels only. 1. controls anD InDIcators: All wiring must conform to applicable local codes, ordinances, and This module is intended for power limited wiring only. Install module wiring in accordance with the job drawings and appropri- wiring diagrams. Set the address on the module per job drawings. Secure module to electrical box (supplied by installer), as shown in 2. 3. typIcal 2-WIre InItIatIng DevIce cIrcuIt (IDc) confIguratIon, nfpa style B (class B): NEXT NUMBER OF UL LISTED CONTACT DEVICES MAY BE USED. DO MIX FIRE ALARM INTIATING, OR SECURITY DEVICES THE SAME MODULE. EOL DEVICE CIRCUIT (IDC) – NFPA STYLE B LIMITED: 450 MAX. @ 11 VDC MAX CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS. WIRING SHOWN IS SUPERVISED AND POWER LIMITED 4. typIcal 4-WIre fault tolerant InItIatIng DevIce cIrcuIt (IDc) confIguratIon, nfpa style D (class a): OR MODULES TO LISTED CONTROL PANELS ONLY LINE CIRCUIT (SLC) VDC MAX. PAIR RECOMENDED OR MODULES TO LISTED CONTROL PANELS ONLY LINE CIRCUIT (SLC) VDC MAX. PAIR RECOMENDED NEXT NUMBER OF UL LISTED CLOSURE DEVICES BE USED. DO NOT MIX FIRE INTIATING, SUPERVISORY, SECURITY DEVICES ON THE MODULE. RESISTOR INTERNAL TERMINALS & 9 CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS. WIRING SHOWN IS SUPERVISED AND POWER LIMITED FireLite Alarms Inc.