Home » System Sensor RR2 Manual
File preview
Click the button below to download immediately for free
Download “System Sensor RR2 Manual” System_Sensor_RR2_Manual.pdf – Downloaded 0 times – 693 KB
Show text preview
INSTALLATION AND MAINTENANCE INSTRUCTIONS Polarity Reversal Module Voltage Range: 8.5 to 35 VDC Operating Current: 25mA Contacts: 2A at 35 VDC Temperature Range: 0 to 55 C (32 to 131 F) Humidity Range: 5% to 95% non-condensing 21 x 21 x 1 connections: 18 AWG stranded, tinned, 16 long Ohio Avenue, St. Charles, Illinois 60174 FAX: 630-377-6495 In an alarm condition, a wiring-fault state may also register at the panel the RR2 is used. Description RR2 polarity reversing relay module is intended for with 2-wire and 4-wire detectors with built-in sounder, as System Sensor 2100AT, 2112/24AT, 2112/24ATR 2112/24AITR, 501BH, and other compatible models. It designed to allow all the detectors in the same loop to when one of the detectors goes into alarm. RR2 may be used with an alarm zone that provides output for fire and continuous output for burglary. default the RR2 will only trigger when the alarm output coded. In this manner, smoke detectors will only sound the result of a fire, and not from a burglary alarm. the RR2 is used in this mode, the smoke detectors provide for coded alarm signals if required by the RR2 can also be set to only trigger on continuous zone signals. When used in this mode, it will not from a coded fire alarm signal. This manual shall be left with the owner/user of equipment. If your panel configuration does not match any of provided wiring diagrams, please contact System Sensor services at 1-800-SENSOR2 for assistance. a mounting location in the control panel within of the provided wire leads. Use a water/isopropyl mixture (50/50) to clean the mounting surface. surface to dry and remove paper backing from the and catch. Stick the Velcro in the panel and the catch the back of the module, then mount the module inside control panel. Route terminals to the appropriate termi- as noted below. calculating total current draw of the control panel, to add current consumption (25mA) for the reversal relay module (RR2). If the fire alarm output signal is coded, set switch on the RR2 to If the fire alarm output is continuous, set the switch to All polarities must be observed! Connect the RR2 module trigger wire to the fire alarm terminals. Alarm/Bell output: (Figures 1 and 2) Connect the purple wire to the Alarm or Bell output. Alarm relay, normally open contact: (Figures 3 and 4) 1. Connect one end of the alarm relay contact output positive auxiliary or detector power fire alarm 2. Connect the purple wire to the other end of the relay contact output. Connect the red and black wires to the panel auxiliary detector power (red to positive, black to negative). 2-wire models Connect the yellow and orange wires to the panel initiat- circuit (yellow to positive, orange to negative). 4-wire models Connect the yellow and orange wires to the panel detec- power circuit (yellow to positive, orange to nega- 2-wire models Connect the brown and white wires to the smoke detector circuit (brown to positive, white to negative). 4-wire models Connect the brown and white wires to the smoke detec- power circuit (brown to positive, white to negative). 1 I56-1683-02 If your panel configuration does not match any of the following wiring diagrams, please contact System Sensor services at 1-800-SENSOR2 for assistance. Please refer to Figures 5 and 6 for Ademco Vista panels and Figure for DSC Power 832 panels. 1. 2-Wire system triggered from IAC/bell circuit:
INSTALLATION AND MAINTENANCE INSTRUCTIONS Polarity Reversal Module Voltage Range: 8.5 to 35 VDC Operating Current: 25mA Contacts: 2A at 35 VDC Temperature Range: 0 to 55 C (32 to 131 F) Humidity Range: 5% to 95% non-condensing 21 x 21 x 1 connections: 18 AWG stranded, tinned, 16 long Ohio Avenue, St. Charles, Illinois 60174 FAX: 630-377-6495 In an alarm condition, a wiring-fault state may also register at the panel the RR2 is used. Description RR2 polarity reversing relay module is intended for with 2-wire and 4-wire detectors with built-in sounder, as System Sensor 2100AT, 2112/24AT, 2112/24ATR 2112/24AITR, 501BH, and other compatible models. It designed to allow all the detectors in the same loop to when one of the detectors goes into alarm. RR2 may be used with an alarm zone that provides output for fire and continuous output for burglary. default the RR2 will only trigger when the alarm output coded. In this manner, smoke detectors will only sound the result of a fire, and not from a burglary alarm. the RR2 is used in this mode, the smoke detectors provide for coded alarm signals if required by the RR2 can also be set to only trigger on continuous zone signals. When used in this mode, it will not from a coded fire alarm signal. This manual shall be left with the owner/user of equipment. If your panel configuration does not match any of provided wiring diagrams, please contact System Sensor services at 1-800-SENSOR2 for assistance. a mounting location in the control panel within of the provided wire leads. Use a water/isopropyl mixture (50/50) to clean the mounting surface. surface to dry and remove paper backing from the and catch. Stick the Velcro in the panel and the catch the back of the module, then mount the module inside control panel. Route terminals to the appropriate termi- as noted below. calculating total current draw of the control panel, to add current consumption (25mA) for the reversal relay module (RR2). If the fire alarm output signal is coded, set switch on the RR2 to If the fire alarm output is continuous, set the switch to All polarities must be observed! Connect the RR2 module trigger wire to the fire alarm terminals. Alarm/Bell output: (Figures 1 and 2) Connect the purple wire to the Alarm or Bell output. Alarm relay, normally open contact: (Figures 3 and 4) 1. Connect one end of the alarm relay contact output positive auxiliary or detector power fire alarm 2. Connect the purple wire to the other end of the relay contact output. Connect the red and black wires to the panel auxiliary detector power (red to positive, black to negative). 2-wire models Connect the yellow and orange wires to the panel initiat- circuit (yellow to positive, orange to negative). 4-wire models Connect the yellow and orange wires to the panel detec- power circuit (yellow to positive, orange to nega- 2-wire models Connect the brown and white wires to the smoke detector circuit (brown to positive, white to negative). 4-wire models Connect the brown and white wires to the smoke detec- power circuit (brown to positive, white to negative). 1 I56-1683-02 If your panel configuration does not match any of the following wiring diagrams, please contact System Sensor services at 1-800-SENSOR2 for assistance. Please refer to Figures 5 and 6 for Ademco Vista panels and Figure for DSC Power 832 panels. 1. 2-Wire system triggered from IAC/bell circuit: