System Sensor L-Series Horn Strobes, Chime Strobes, and Strobes - Wall (I56-5845)

I Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 AND MAINTENANCE INSTRUCTIONS Output Strobes Chime Strobes Strobes Wall Mount use with the following models Wall Mount Horn Strobes P2RL P2WL P2RL P P2WL P P2RL SP P2WL SP Wall Mount Horn Strobes P2GRL P2GWL Wall Mount Chime Strobes CHSRL CHSWL Wall Mount Strobes SRL SWL SRL P SWL P SRL SP SWL CLR ALERT Wall Mount Strobes SGRL SGWL SPECIFICATIONS Operating Temperature Range Flash Rate Voltage Voltage Range Voltage with MDL3 Sync Module 8.5 to 17.5V 12V nominal or 16.5 to 33V 24V nominal terminal wire gauge FOR PRODUCTS AND ACCESSORIES to 120 0 to 49 to 93 Non condensing flash per second 12VDC or regulated 24DC FWR to 17.5V 12V nominal or 16 to 33V 24V nominal to 18 AWG PRODUCTS Strobe Chime Strobe and Horn Strobe 143mm 119mm 32mm Strobe and Horn Strobe 133 mm 88 mm 49 mm device with SBBRL WL Surface Mount Back Box 149 mm 125 mm 47 mm device with SBBGRL WL Surface Mount Back Box SBBRL WL Surface Mount Back Box intended only for standard horn strobes chime strobes and strobes Surface Mount Back Box intended for compact horn strobes and strobes 140 mm 94 mm 39 mm x 4 x 1 Single Gang Double Gang 4 Octagon SBBRL WL wall SBBGRL WL wall Gang SBBGRL WL wall BOX OPTIONS 2 Wire Indoor Products 2 Wire Indoor Products This manual shall be left with the owner user of this equipment INSTALLING read the System Sensor Audible Visible Application Reference Guide provides detailed information on notification devices wiring and applications Copies of this manual are available from System Sensor 72 and NEMA guidelines should be observed The notification appliance used must be tested and maintained NFPA 72 requirements DESCRIPTION Sensor series of notification appliances offer a wide range of audible visible devices for life safety notification Our 2 wire horn strobes chime and strobes come with 8 field selectable tone and volume combina and 7 field selectable candela settings Intended for indoor applications approved for wall mount installations only Available in two attractive designs standard and compact horn strobe and strobe only horn strobes and strobes are public mode notification appliances in to alert occupants of a life safety event The 2 wire chime strobe is private mode notification appliance The horn is listed to ANSI UL 464 public mode and the strobe is listed to ANSI UL 1638 pub mode 2 wire chime strobe is a private mode notification appliances in to alert trained personnel to investigate a life safety event and take actions The chime portion of the chime strobe is listed to ANSI 464 private mode and the strobe portion is listed to ANSI UL 1638 pri mode Sensor notification appliances are designed to be used in either 12 24VDC or 24V FWR full wave rectified systems System Sensor AV de can be activated by a compatible fire alarm control panel or power sup Refer to the appropriate fire alarm control panel manufacturer or power for more information Sensor wall 2 wire horn strobes 2 wire chime strobes and strobes are backward compatible with the previous generation since 1996 notification appliances They come enabled with System Sensor synchro protocol which requires connections to a power supply capable of the System Sensor synchronization pulses a FACP NAC output to System Sensor synchronization protocol or the use of MDL3 to generate the synchronization protocol ALARM SYSTEM CONSIDERATIONS National Fire Alarm and Signaling Code NFPA 72 requires that all noti appliances used for building evacuation installed after July 1 1996 temporal coded signals Signals other than those used for evacuation do not have to produce the temporal coded signal System Sensor spacing notification appliances in compliance with NFPA 72 DESIGN system designer must make sure that the total current draw by the devices the loop does not exceed the current capability of the panel supply and the last device on the circuit is operated within its rated voltage The draw information for making these calculations can be found in the within the manual For convenience and accuracy use the voltage drop on the System Sensor website www systemsensor com calculating the voltage available to the last device it is necessary to the voltage due to the resistance of the wire The thicker the wire the the voltage drop Wire resistance tables can be obtained from electri handbooks Note that if Class A wiring is installed the wire length may up to twice as long as it would be for circuits that are not fault tolerant total number of strobes on a single NAC must not exceed 69 for 24 volt TONES Sensor offers a wide variety of tones for your life safety needs includ temporal 3 pattern second on second off second on second second on 1 off and repeat which is specified by ANSI and NFPA 72 standard emergency evacuation signaling select the tone turn the rotary switch on the back of the product to the setting See Figure 1 horn settings can be found in Table 1 Available chime settings can found in Table 2 1 HORN TONES KHz Temporal KHz Temporal KHz Non Temporal KHz Non Temporal 2 CHIME TONES Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Setting Setting CANDELA SETTINGS Sensor offers a wide range of candela settings for your life safety In order to select your candela output adjust the slide switch on the of the product to the desired candela setting on the selector switch See 2 candela setting can also be verified by looking into the small window on front of the unit See Table 3 for candela settings for wall products All meet the light output profiles specified in the appropriate UL Stan See Figures 3 and 4 DRAW AND AUDIBILITY RATINGS the strobe the current draw for each setting is listed in Table 3 For the strobe the current draw and audibility settings are listed in Table 4 For chime strobe the current draw and audibility settings are listed in Table 5 1 AUDIO SELECTOR 2 CANDELA SELECTOR 3 LIGHT OUTPUT DISPERSION 4 VERTICAL WALL TO FLOOR of of 45 the left 45 the right is generated text for of degree is permitted AND MOUNTING wiring must be installed in compliance with the National Electric Code the local codes as well as the authority having jurisdiction Wiring must be of such length or wire size which would cause the notification appli to operate outside of its published specifications Improper connections prevent the system from alerting occupants in the event of an emergency sizes up to 12 AWG 2.5 mm may be used with the mounting plate The plate ships with the terminals set for 12 AWG wiring wire connections by stripping about 3 8 of insulation from the end of wire Then slide the bare end of the wire under the appropriate clamping and tighten the clamping plate screw provide a wire strip guide See Figure 5 for wiring terminals and strip reference finish should not be altered Do not paint not over tighten mounting plate screws this may cause mounting plate flex 5 WIRING TERMINALS SHORTING SPRING AND STRIP GUIDE Spring A0517 00 3 WALL MOUNT STROBE CURRENT DRAW mA Volts