System Sensor RR1 Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS Polarity Reversal Module Voltage Range Operating Current Contacts Temperature Range Humidity Range connections to 32 VDC at 30 VDC 0.5A at 120 VAC to 55 C 32 cid 176 to 131 cid 176 F to 95 x 13 4 AWG stranded tinned 16 long Description RR1 polarity reversing relay module is intended for with 2 wire and 4 wire detectors with built in such as System Sensor 2100AT 2112 24ATR 2112 24AITR and other compatible models It is de to allow all the detectors in the same loop to when one of the detectors goes into alarm This manual shall be left with the owner user of equipment 2 wire models If your panel configuration does not match any of provided wiring diagrams please contact System Sen technical services at 1 800 SENSOR2 for assistance a mounting location in the control panel within of the provided wire leads Use a water isopropyl al mixture 50 50 to clean the mounting surface Allow to dry and remove paper backing from the Velcro catch Stick the Velcro in the panel and the catch on back of the module then mount the module inside the panel Route terminals to the appropriate terminals noted below Connect the relay module trigger wires to the fire alarm terminals Polarity must be observed Continuous alarm bell output Figures 1 and 2 red wire to positive and black wire to negative Alarm relay normally open contact output Figures 3 4 Connect one end of the alarm relay contact output the black wire to positive and negative of respectively Auxiliary power supply is used a power source for 2 wire detectors and power the detectors is used as a power source for 4 Division of Pittway 3825 Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 If using a power supervision relay be of the following In an alarm condition a trouble state may also register at panel when the RR1 is used RR1 cannot be used with a coded or power supply For proper RR1 opera distinct wiring methods are required See 4 for specifics Connect the red wire to other end of alarm relay detectors output Connect the outgoing wires of the relay module to the detector power in terminals brown to positive to negative Connect the blue and purple wires of the RR1 to any of power sources as specified in the applicable wiring see Figures 1 4 the yellow and orange wires to the positive and of the initiating loop respectively models the yellow and orange wires to the positive and of power to detectors respectively Connect the smoke detector initiating circuit to the loop calculating total current draw of the control panel to add current consumption 29mA for the reversal relay module RR1 testing notify the proper authorities that the system undergoing maintenance and will temporarily be out of in accordance with NFPA 72 Chapter 7 test methods and testing frequency To test the RR1 module confirm that the smoke detec do not sound without an alarm Initiate an alarm with smoke or approved test method any detector connected to the control panel via the module In alarm all the detectors that are installed the corresponding loop shall sound Reset the detectors by removing power to the loop If your panel configuration does not match any of the following wiring diagrams please contact System Sensor services at 1 800 SENSOR2 for assistance 1 RR1 module with 2 wire smoke detectors power reversal relay module does not provide supervision supervision is provided by the interconnected control unit REVERSAL MODULE RR1 LISTED auxiliary power IAC Bell output or UL listed regulated power supply for fire protective signaling use shown with panel in alarm If optional Class A wiring is used second power reversal relay module RR1 must be added to enable concurrent polarity reversal 2 RR1 module with 4 wire smoke detectors power reversal relay module does not provide supervision supervision is provided by the interconnected control unit REVERSAL MODULE RR1 auxiliary power detector power IAC Bell or any UL listed regulated power supply for fire protective signaling use shown with panel in alarm LISTED POWER SHOWN 12 24V RESISTOR BY CLASS A WIRING 3 RR1 module with alarm relay and 2 wire smoke detectors power reversal relay module does not provide supervision supervision is provided by the interconnected control unit REVERSAL MODULE RR1 LISTED contact auxiliary power IAC Bell output or UL listed regulated power supply for fire protective signaling use shown with panel in alarm If optional Class A wiring is used second power reversal relay module RR1 must be added to enable concurrent polarity reversal 4 RR1 module with alarm relay and 4 wire smoke detectors power reversal relay module does not provide supervision supervision is provided by the interconnected control unit REVERSAL MODULE RR1 LISTED contact auxiliary power detector power IAC Bell or any UL listed regulated power supply for fire protective signaling use shown with panel in alarm POWER SHOWN 12 24V RESISTOR BY CLASS A WIRING Conditions Required for Proper Operation of the RR1 Upon Fire Alarm 2 Wire Model Smoke Detectors Model 2100AT power supply for smoke detector sounders upon alarm and one of the following Bell alarm or programmable output exclusive to fire alarm Output of minimum 30mA 9.5 Vdc required Auxiliary power supply for RR1 and auxiliary relay with normally open contact activated by fire alarm only 4 Wire Model Smoke Detectors Models 2112 24AT 2112 24ATR 2112 24AITR Bell alarm or programmable output exclusive to fire alarm Output of minimum 30mA 9.5 Vdc required Auxiliary relay with normally open contact activated by fire alarm only Outputs must be continuous non coded non pulsed The RR1 will not function properly in panels that provide single combined burglary and fire alarm output unless the minimum conditions noted above are present Limited Warranty Sensor warrants its enclosed relay module to be free from defects materials and workmanship under normal use and service for a period three years from date of manufacture System Sensor makes no other warranty for this relay module No agent representative dealer or of the Company has the authority to increase or alter the obliga or limitations of this Warranty The Company obligation of this shall be limited to the repair or replacement of any part of the