System Sensor RTS151 Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS Test Station Requirements Alarm LED Coil Current Switch Switch Response Time H 2.90 W 1.4 D lbs 32 VDC 10 mA max mA max VA 32 VDC VA 32 VDC sec max to 60 14 to 140 RH Non condensing Max FM CE RTS151 replaces RTS451 This manual shall be left with the owner user of this equipment A test coil is required only for use with D2 DNR DH400 DH500 mod For D2 models order part DCoil For the DH400 500 models order part Coil INFORMATION Sensor RTS151 is an automatic fire detector accessory designed to a remotely located detector Consult detector installation instructions for information National Fire Protection Association has published codes standards and practices for the installation and use of the above product It is that the installer be familiar with these requirements with local and any special requirements of the local authority having jurisdiction CONTENTS RTS151 remote test station screw pack 2 mounting screws M02 04 test magnet OF RTS151 the appropriate detector installation instructions for the applicable diagram The RTS151 mounts to a single gang box 2 1 2 minimum or directly to the wall or ceiling Figure 8 for wiring diagram of RTS151 with Duct Smoke Detectors Canadian applications the RTS151 is intended to be located in the same as the smoke detector and within 60 feet of the unit Function and hold the painted side of the magnet to the test location RTS151 Indication the magnet in place some time will elapse 40 sec maximum depend on the detector type before the alarm indicating LED will light Function insert a 1 8 maximum diameter tool into the hole until it stops and turns off The RTS151 is capable of resetting only certain System Sensor of detectors Refer to detector installation instructions for additional 3825 Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 1 RTS151 REMOTE TEST STATION 2 WIRING DIAGRAM FOR RTS151 TO D4120 4 WIRE DUCT DETECTOR LED OUT OUT TEST RESET 3 WIRING DIAGRAM FOR RTS151 TO DNR 2 WIRE DUCT DETECTOR WITH REMOTE TEST CAPABLE HEAD COIL COIL CONV ONLY 4 WIRING DIAGRAM FOR RTS151 TO D2 2WIRE DUCT SMOKE DETECTOR RED REMOTE STATION TEST COIL TEST COIL VDC POWER USER VDC POWER USER VAC 10 WAVE RECTIFIED POWER BE USED VAC 10 WAVE RECTIFIED POWER BE USED RED REMOTE STATION IN OUT RA RA RTS TEST COIL TEST COIL IN OUT RA RA RTS 1 AUX POWER LOCATED AT DUCT DETECTOR 2 AUX POWER LOCATED TEST STATION THE USE OF THE RTS151 REQUIRES THE INSTALLATION OF ACCESSORY COIL DCOIL SOLD SEPARATELY 5 WIRING DIAGRAM FOR RTS151 TO DH100ACDC 4 WIRE SMOKE DETECTOR 6 WIRING DIAGRAM FOR RTS151 TO DH100 2 WIRE DUCT DETECTOR Signal Power LED Alarm Reset Reset Out Connection 8 WIRING DIAGRAM FOR RTS151 TO BEAM1224 BEAM1224S DETECTOR 7 WIRING DIAGRAM FOR RTS151 TO DH400ACDC DUCT DETECTOR SIGNAL POWER RESET ALARM OUT LED ALARM INPUT INPUT YELLOW LED TROUBLE OUTPUT LIMITED WARRANTY Sensor warrants its enclosed product to be free from defects in materials and under normal use and service for a period of three years from date of System Sensor makes no other express warranty for the enclosed product agent representative dealer or employee of the Company has the authority to in or alter the obligations or limitations of this Warranty The Company obligation this Warranty shall be limited to the replacement of any part of the product which is to be defective in materials or workmanship under normal use and service during three year period commencing with the date of manufacture After phoning System toll free number 800 SENSOR2 736 7672 for a Return Authorization number defective units postage prepaid to Honeywell 12220 Rojas Drive Suite 700 El Paso 79936 USA Please include a note describing the malfunction and suspected cause failure The Company shall not be obligated to replace units which are found to be because of damage unreasonable use modifications or alterations occurring the date of manufacture In no case shall the Company be liable for any consequen or incidental damages for breach of this or any other Warranty expressed or implied even if the loss or damage is caused by the Company negligence or fault states do not allow the exclusion or limitation of incidental or consequential dam so the above limitation or exclusion may not apply to you This Warranty gives you legal rights and you may also have other rights which vary from state to state System Sensor 06 10