System Sensor SAA Indoor Ceiling Strobes Horn Strobes

Indoor Selectable Strobes and Strobes for Applications Advance audible visible notification products rich with features guaranteed to cut installation times maximize profits Plug in design with minimal intrusion into the back box Tamper resistant construction Automatic selection of 12 or 24 volt operation at 15 and candela Field selectable candela settings on ceiling units 15 15 75 30 95 110 115 135 150 177 and 185 Horn rated at 88 dBA at 16 volts Rotary switch for horn tone and three volume selections Universal mounting plate for ceiling units Mounting plate shorting spring feature checks wiring continuity device installation Electrically Compatible with legacy SpectrAlert devices Compatible with MDL3 sync module Listed for ceiling or wall mounting Listings chimes horn strobes horns strobes indoor strobes horn strobes strobes horns chimes SpectrAlert Advance series offers the most versatile and line of horns strobes and horn strobes in the industry white and red plastic housings wall and ceiling mounting and plain and FIRE printed devices SpectrAlert Advance meet virtually any application requirement the entire SpectrAlert Advance product line ceiling mount and horn strobes include a variety of features that increase application versatility while simplifying installation All devices a plug in design with minimal intrusion into the back box installations fast and foolproof while virtually eliminating and time consuming ground faults further simplify installation SpectrAlert Advance utilizes a mounting plate so you can mount them to a wide array back boxes With an onboard shorting spring installers can test continuity before the device is installed can also easily adapt devices to a suit a wide range of requirements using field selectable candela settings selection of 12 or 24 volt operation and a rotary switch horn tones with three volume selections Advance Specifications Specifications Advance strobes and horn strobes shall mount to a standard 4 4 1 back box 4 inch octagon back box or double back box Two wire products shall also mount to a single gang 2 4 17 back box A universal mounting plate shall be used for ceiling and wall products The notification appliance circuit wiring shall terminate at the universal mounting plate Also SpectrAlert products when used with the Sync Module accessory shall be powered from a non coded notification appliance circuit and shall operate on a nominal 12 or 24 volts When used with the Sync Module 12 volt rated notification appliance circuit shall operate between 8.5 and 17.5 volts 24 volt rated notification appliance circuit outputs shall operate between 16.5 and 33 Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full wave rectified power supply Strobes and horn strobes shall have field selectable candela settings including 15 15 75 30 75 95 110 115 135 177 and 185 strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service strobe shall be wired as a primary signaling notification appliance and comply with the Americans with Disabilities Act requirements for signaling appliances flashing at 1 Hz over the strobe entire operating voltage range The strobe light shall consist of a xenon flash and associated lens reflector system Strobe Combination horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for protective service The horn strobe shall be wired as a primary signaling notification appliance and comply with the Americans with Act requirements for visible signaling appliances flashing at 1 Hz over the strobe entire operating voltage range The strobe light consist of a xenon flash tube and associated lens reflector system The horn shall have three audibility options and an option to switch a temporal three pattern and a non temporal continuous pattern These options are set by a multiple position switch On four wire the strobe shall be powered independently of the sounder The horn on horn strobe models shall operate on a coded or non coded supply Module module shall be a System Sensor Sync model MDL3 listed to UL 464 and shall be approved for fire protective service The module synchronize SpectrAlert strobes at 1 Hz and horns at temporal three Also while operating the strobes the module shall silence the horns horn strobe models over a single pair of wires The module shall mount to a 4 11 4 11 2 1 back box The module shall also two Style Y class B circuits or one Style Z class A circuit The module shall synchronize multiple zones Daisy chaining two or more modules together will synchronize all the zones they control The module shall not operate on a coded power supply Specifications Operating Temperature Range Flash Rate Voltage Voltage Range2 Voltage Range MDL3 Terminal Wire Gauge Dimensions including lens Surface Mount Back Box Skirt Dimensions SBBCW Full Wave Rectified FWR voltage is a non regulated time varying power source that is used on some power supply and panel outputs P S PC and SC products will operate at 12 V nominal only for 15 and 15 75 cd to 120 0 to 49 to 93 non condensing flash per second 12 DC FWR or regulated 24 DC FWR1 to 17.5 V 12 V nominal or 16 to 33 V 24 V nominal to 17.5V 12 V nominal or 16.5 to 33 V 24V nominal to 18 AWG diameter 2.5 high 173 mm diameter 64 mm high diameter x 3.4 high 175 mm diameter x 86 mm high Current Draw Data Max Strobe Current Draw mA RMS Candela Range Max Current Draw mA RMS 2 Wire Horn Strobe Standard Candela Range 15 cd Volts Volts Volts Volts Volts Input High Medium Low High Medium Low Volts Range Input High Medium Low High Medium Low Input High Medium Low High Medium Low Input High Medium Low High Medium Low Max Current Draw mA RMS 2 Wire Horn Strobe High Candela Range 135 cd Strobe Tones and Sound Output Data Strobe Output dBA 7 8 and 9 are not available on 2 wire horn strobes Pattern Nominal