System Sensor SAA Indoor Wall Horns Strobes Horn Strobes

Indoor Selectable Horns and Strobes for Applications Advance audible visible notification products rich with features guaranteed to cut installation times maximize profits Plug in design with minimal intrusion into the back box Tamper resistant construction Automatic selection of 12 or 24 volt operation at and 15 75 candela Field selectable candela settings on wall units 15 15 75 75 95 110 115 135 150 177 and 185 Horn rated at 88 dBA at 16 volts Rotary switch for horn tone and three volume selections Universal mounting plate for wall units Mounting plate shorting spring checks wiring continuity before installation Electrically Compatible with legacy SpectrAlert devices Compatible with MDL3 sync module Listed for ceiling or wall mounting Listings chimes horn strobes horns strobes indoor strobes horn strobes strobes horns chimes SpectrAlert Advance series offers the most versatile and line of horns strobes and horn strobes in the industry white and red plastic housings wall and ceiling mounting and plain and FIRE printed devices SpectrAlert Advance meet virtually any application requirement the entire SpectrAlert Advance product line wall mount horns and horn strobes include a variety of features that increase application versatility while simplifying installation All devices plug in designs with minimal intrusion into the back box installations fast and foolproof while virtually eliminating and time consuming ground faults further simplify installation and protect devices from construction SpectrAlert Advance utilizes a universal mounting plate an onboard shorting spring so installers can test wiring before the device is installed can also easily adapt devices to a suit a wide range of requirements using field selectable candela settings selection of 12 or 24 volt operation and a rotary switch horn tones with three volume selections Advance Specifications Specifications Advance horns strobes and horn strobes shall mount to a standard 4 4 1 back box 4 inch octagon back box or back box Two wire products shall also mount to a single gang 2 4 17 back box A universal mounting plate shall used for mounting ceiling and wall products The notification appliance circuit wiring shall terminate at the universal mounting plate SpectrAlert Advance products when used with the Sync Module accessory shall be powered from a non coded notification circuit output and shall operate on a nominal 12 or 24 volts When used with the Sync Module 12 volt rated notification circuit outputs shall operate between 8.5 and 17.5 volts 24 volt rated notification appliance circuit outputs shall operate between and 33 volts Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full rectified unfiltered power supply Strobes and horn strobes shall have field selectable candela settings including 15 15 75 30 75 95 115 135 150 177 and 185 strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service strobe shall be wired as a primary signaling notification appliance and comply with the Americans with Disabilities Act requirements for signaling appliances flashing at 1 Hz over the strobe entire operating voltage range The strobe light shall consist of a xenon flash and associated lens reflector system Strobe Combination horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for protective service The horn strobe shall be wired as a primary signaling notification appliance and comply with the Americans with Act requirements for visible signaling appliances flashing at 1 Hz over the strobe entire operating voltage range The strobe light consist of a xenon flash tube and associated lens reflector system The horn shall have three audibility options and an option to switch a temporal three pattern and a non temporal continuous pattern These options are set by a multiple position switch On four wire the strobe shall be powered independently of the sounder The horn on horn strobe models shall operate on a coded or non coded supply Module module shall be a System Sensor Sync model MDL3 listed to UL 464 and shall be approved for fire protective service The module synchronize SpectrAlert strobes at 1 Hz and horns at temporal three Also while operating the strobes the module shall silence the horns horn strobe models over a single pair of wires The module shall mount to a 411 411 21 back box The module shall also two Style Y class B circuits or one Style Z class A circuit The module shall synchronize multiple zones Daisy chaining two or more modules together will synchronize all the zones they control The module shall not operate on a coded power supply Specifications Operating Temperature Range Flash Rate Voltage Voltage Range2 Voltage Range MDL3 Sync Module Terminal Wire Gauge Dimensions including lens Dimensions Trim Ring Dimensions sold as a 5 pack TR HS to 120 0 to 49 to 93 non condensing flash per second 12 DC FWR or regulated 24 DC FWR1 to 17.5 V 12 V nominal or 16 to 33 V 24 V nominal to 17.5 V 12 V nominal or 16.5 to 33 V 24 V nominal to 18 AWG L 4.7 W 2.5 D 142 mm L 119 mm W 64 mm D L 4.7 W 1.3 D 142 mm L 119 mm W 33 mm D L 4.8 W 0.35 D 145 mm L 122 mm W 9 mm D Full Wave Rectified FWR voltage is a non regulated time varying power source that is used on some power supply and panel outputs P S PC and SC products will operate at 12 V nominal only for 15 and 15 75 cd Current Draw Data Max Strobe Current Draw mA RMS Volts Volts Max Horn Current Draw mA RMS Pattern Volts Volts Max Current Draw mA RMS 2 Wire Horn Strobe Standard Candela Range 15 cd Input High Medium Low High Medium Low Input High Medium Low High Medium Low Input High Medium Low High Medium Low Volts Volts Volts Input High Medium Low High Medium Low Volts Max Current Draw mA RMS 2 Wire Horn Strobe High Candela Range 135 cd Tones and Sound Output Data and Horn Strobe Output dBA FWR Sound Pattern