System Sensor SAA Indoor Wall Speakers Speaker Strobes

Indoor Selectable Speaker and Dual Evacuation for Wall SpectrAlert Advance selectable output speaker and dual voltage evacuation speakers can reduce faults and enable faster installation Plug in design and protective cover reduce ground faults Universal mounting plate with an onboard shorting spring tests continuity before installation No extension ring required Field selectable candela settings 15 15 75 30 75 95 110 115 135 150 177 185 Automatic selection of 12 or 24 volt operation at 15 15 75 candela Rotary switch simplifies field selection of speaker voltage and 70.7 Vrms and power settings 1 and 2 watts SP speakers offer high fidelity sound output SPV speakers offer high volume sound output Compatible with System Sensor synchronization protocol Electrical compatibility with existing SpectrAlert products Tamper resistant construction Listed for ceiling or wall mounting Listings SpectrAlert Advance Series of speakers and speaker reduce costly ground faults using a plug in design and mounting plate that allow the installer to pre wire mounting dress the wires and confirm wiring continuity before plugging the speakers In addition a protective plastic cover prevents wires by covering exposed speaker components devices also enable faster installations by providing instant to ensure that wiring is properly connected rotary switches select voltage and power settings and 11 field selectable candela for both wall and ceiling speaker strobes low total harmonic distortion of the SP speaker offers high fidelity output while the SPV speaker offers high volume sound output use in high ambient noise applications Advance makes installation easy Attach a universal mounting plate to a 4 4 21 inch back box applications do not require an extension ring Connect the notification appliance circuit or speaker wiring to the on the mounting plate Attach the speaker or speaker strobe to the mounting plate by the product tabs into the mounting plate grooves Hinge device into position to lock the product pins into the mounting terminals The device will temporarily hold in place with a until it is secured with a captured mounting screw Advance Speaker and Speaker Strobe Specifications Specifications Advance speaker and speaker strobes shall mount to a 4 4 21 back box A universal mounting plate shall be used for ceiling and wall products The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate Also Advance speaker strobes when used with the Sync Module accessory shall be powered from a non coded notification circuit output and shall operate on a nominal 12 or 24 volts When used with the Sync Module 12 volt rated notification circuit outputs shall operate between 8.5 and 17.5 volts 24 volt rated notification appliance circuit outputs shall operate between and 33 volts Indoor SpectrAlert Advance products shall operate between 32 and 120 from a regulated DC or full wave rectified power supply Speaker strobes shall have field selectable candela settings including 15 15 75 30 75 95 110 115 135 150 185 speaker shall be a System Sensor SpectrAlert Advance model dual voltage transformer speaker capable of operating at 25.0 or nominal Vrms It should be listed to UL 1480 and shall be approved for fire protective service The speaker shall have a frequency range 400 to 4,000 Hz and shall have an operating temperature between 32 and 120 The speaker shall have power taps and voltage that are by rotary switches Strobe combination speaker strobe shall be a System Sensor SpectrAlert Advance model listed to UL1480 and UL 1971 and be approved for fire signaling systems The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch and shall a frequency range of 400 to 4,000 Hz The speaker shall have power taps that are selected by rotary switch The strobe shall comply with NFPA 72 requirements for visible signaling appliances flashing at 1 Hz over the strobe entire operating voltage range The strobe light consist of a xenon flash tube and associated lens reflector system Module module shall be a System Sensor Sync model MDL3 listed to UL 464 and shall be approved for fire protective service The module synchronize SpectrAlert strobes at 1 Hz The module shall mount to a 411 411 21 back box The module shall also two Style Y class B circuits or one Style Z class A circuit The module shall synchronize multiple zones Daisy chaining two or more modules together will synchronize all the zones they control The module shall not operate on a coded power supply in 127 mm in 127 mm in 130 mm in 127 mm in 71 mm in 74 mm in 86 mm in 119 mm in 152 mm in 130 mm in 135 mm Specifications Temperature Range Wall Mount Speaker Speaker Surface Mount Back Box Speaker Strobe lens and speaker Surface Mount Back Box Specifications Voltage speakers Supervisory Voltage speakers Flash Rate Voltage strobes Voltage Range includes fire panels with built in sync Voltage with MDL3 Sync Module Range to 120 0 to to 93 non in 152 mm in 152 mm in 152 mm in 152 mm Volts or 70.7 Volts VDC flash per second 12 VDC or regulated 24 to 17.5 V 12 V or 16 to 33V V nominal to 17.5 V 12 V or 16.5 to 24 V nominal to 4000 Hz 1 2 watts Current Draw Data Max Strobe Current Draw mA RMS Range Range Output Reverberant dBA 10 ft SP Series SPV Series SPS Series SPSV Series to 17.5 Volts NA to 33 Volts W W SP Speaker SPS Speaker Strobe Mounting Speaker Strobe with SBBSPR Surface Mount Back Information for SpectrAlert Advance Speakers and Speaker Strobes Mount only only High dB Strobe Standard cd Speaker Strobe Standard cd Strobe Standard cd Amber Lens Strobe Standard cd Clear Lens Strobe High cd Speaker Strobe High cd Strobe Standard cd High dB Speaker Strobe Standard cd High dB in 9.5 in Retrofit Plate Mount Back Box for Speakers and Speaker Strobes Mount Trim Ring P models have a plain housing no marking on the cover cd refers to strobes that include 15 15 75 30 75 95 110 and 115 candela settings cd refers to strobes that include 135 150 177 and 185 candela settings Ohio Avenue St Charles IL 60174 800 SENSOR2 Fax 630 377 6495 specifications subject to change without notice Visit systemsensor com current product information including the latest version of this data sheet System Sensor 2 15