System Sensor SAA MP120K Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS 120 VAC Adapter Mounting Plate Specifications Operating Temperature Range Voltage Voltage Range Draw From AC Line to 151 to 66 to 93 non condensing indoor products 120 VAC VAC mA max Ohio Avenue St Charles Illinois 60174 Fax 630.377.6495 may be used with any of the following products at all horn and strobe settings P2RH P2RK P2RHK P2W P2WH SR SRH SRK SRHK SW SWH PC2R PC2RH PC2RK PC2RHK PC2W PC2WH SCR SCRH SCRK SCRHK SCW HR HRK HW SR P SW P SRH P SWH P P2R P P2W P P2RH P P2WH P SCR P SCW P SCRH P SCWH P PC2R P PC2W P PC2RH P PC2WH P SRH SP P2R SP P2RH SP SCW SP SCWH SP PC2W SP PC2WH SP CHR CHW CHSR CHSW DESCRIPTION MP120K mounting plate is designed to allow the use of 120 VAC to power Advance horns strobes horns strobes chimes and chime The MP120K consists of a SpectrAlert Advance mounting plate that been fitted with a power supply that converts 120VAC to nominal 24V MP120K must be installed using a 120 VAC power source This unit only be used for non synchronous applications it will NOT work with Sync Modules This manual shall be left with the owner user of this equipment module has pig tail wires and is intended to be wired without rigid con inside a standard electrical box 1 NON SYNCHRONIZED DEVICES ANY COMBINATION OF MODELS POWERED BY A 2 WIRE CIRCUIT Only VAC Wire System Mix of Models for Tandem 2 X 4 X 2 1 8 BACK BOX WIRES MOUNTING PLATE MP120K WALL OR CEILING For indoor applications attach the mounting plate as shown in Figure 2 mounting plate is compatible only with 4 4 electrical boxes Connect field wiring For indoor models only If the product is not to be installed at this point use the paint cover to contamination of the mounting plate To attach product to mounting plate remove the paint cover then hook on the product housing into the grooves on mounting plate Then swing product into position to engage the pins on the product with terminals on the mounting plate Make sure that the tabs on the back the product housing fully engage with the mounting plate Secure product by tightening the single mounting screw in the front the product housing For tamper resistance the standard captivated screw may be replaced with the enclosed Torx screw SERIES MOUNTING K Series products may be used indoors or outdoors They must be in using the proper SpectrAlert Advance weatherproof back box Do attempt to use boxes other than the ones supplied with the product The plastic weatherproof back box is equipped with removable side for mounting The back box may be secured directly to the wall ceiling using the flanges plastic and metal back boxes or by using knockout plugs plastic back boxes Knockout plugs are provided to directly to the wall or ceiling or to a 1900 weatherproof electrical see figure 3 The wall mount box must be mounted with its internal post in the lower corner as shown in Figure 3 Threaded holes are provided in the sides of the box for inch conduit Knockout plugs in the back of the box can be used for inch entry Unused holes must be sealed Plugs are provided with the box this purpose It is the responsibility of the installer to make sure that all openings and are sealed properly Outdoor installations that are protected direct exposure to rain are still subject to condensation or leakage hidden areas such as a soffit Water may pool on the back box due to condensation or direct exposure rain or snow Use watertight fittings for all wiring connections includ the knockout plugs on the back of the box When using plastic plugs fill unused threaded holes apply teflon tape and or silicone sealant to the chance of leakage Attach the mounting plate to the weatherproof back box using the four screws supplied Follow steps 1 6 of the indoor mounting instructions to wire and attach product 3 refer to insert for the Limitations of Fire Alarm Systems LIMITED WARRANTY Sensor warrants its enclosed product to be free from defects in materials and under normal use and service for a period of three years from date of System Sensor makes no other express warranty for this product No representative dealer or employee of the Company has the authority to increase alter the obligations or limitations of this Warranty The Company obligation of this shall be limited to the replacement of any part of the product which is found be defective in materials or workmanship under normal use and service during the year period commencing with the date of manufacture After phoning System toll free number 800 SENSOR2 736 7672 for a Return Authorization number defective units postage prepaid to Honeywell 12220 Rojas Drive Suite 700 El Paso 79936 USA Please include a note describing the malfunction and suspected cause failure The Company shall not be obligated to replace units which are found to be because of damage unreasonable use modifications or alterations occurring the date of manufacture In no case shall the Company be liable for any consequen or incidental damages for breach of this or any other Warranty expressed or implied even if the loss or damage is caused by the Company negligence or fault states do not allow the exclusion or limitation of incidental or consequential dam so the above limitation or exclusion may not apply to you This Warranty gives you legal rights and you may also have other rights which vary from state to state Strobes and Horn Strobes have been tested and found to comply with the for a Class B digital device pursuant to part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference when the equip is operated in a commercial environment This equipment generates uses and radiate radio frequency energy and if not installed and used in accordance with the manual may cause harmful interference to radio communications Operation this equipment in a residential area is likely to cause harmful interference in which the user will be required to correct the interference at his own expense System Sensor 06 10 STATEMENT