System Sensor SAA Outdoor Horns Strobes Horn Strobes

Outdoor Selectable Horns Strobes Horn Strobes Advance outdoor selectable output horns and horn strobes are rich with features that installation times and maximize profits Automatic selection of 12 or 24 volt operation at 15 and 15 75 Field selectable candela settings on wall and ceiling units 15 15 75 75 95 110 115 135 150 177 and 185 Plug in design with minimal intrusion into the back box Tamper resistant construction Universal mounting plate for wall and ceiling mount units Mounting plate shorting spring tests wiring continuity before are installed Weatherproof per NEMA 4X IP56 Listed to UL 1638 strobe and UL 464 horn Rated from to 151 Horn rated at 88 dBA at 16 volts Rotary switch for horn tone and three volume selections Compatible with System Sensor synchronization protocol and SpectrAlert products Listings chimes horn strobes horns outdoor and alert strobes outdoor strobes horn strobes strobes horns chimes SpectrAlert Advance series offers the broadest line of horns strobes and horn strobes in the industry With and red plastic housings wall and ceiling mounting options plain and FIRE printed devices SpectrAlert Advance can meet any application requirement Advance outdoor horns strobes and horn strobes can used indoors or outdoors in wet or dry applications and can reliable operation from to 151 the entire SpectrAlert Advance product line these devices a variety of features that increase their application versatility simplifying installation All devices feature plug in designs with intrusion into the back box which make installations fast foolproof while virtually eliminating costly and time consuming faults horns strobes and horn strobes use a universal mounting plate an onboard shorting spring that tests wiring continuity before device is installed protecting devices from damage In addition candela settings automatic selection of 12 or 24 operation and a rotary switch for horn tones with three volume enables installers to easily adapt devices to suit a wide of application requirements Advance Outdoor Horn Strobe and Horn Strobe Specifications Specifications Advance outdoor horns strobes and horn strobes shall mount to a weatherproof back box A universal mounting plate shall be used for mounting and wall products The notification appliance circuit wiring shall terminate at the universal mounting plate Also SpectrAlert Advance products when with the Sync Module accessory shall be powered from a non coded notification appliance circuit output and shall operate on a nominal 12 24 volts When used with the Sync Module 12 volt rated notification appliance circuit outputs shall operate between 9 and 17.5 volts 24 volt rated appliance circuit outputs shall operate between 17 and 33 volts Outdoor SpectrAlert Advance products shall operate between and 151 degrees from a regulated DC or full wave rectified unfiltered power supply Strobes and horn strobes shall have field selectable candela settings including 15 30 75 95 110 115 135 150 177 and 185 strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service The strobe shall be as a primary signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances flashing at Hz over the strobe entire operating voltage range The strobe light shall consist of a xenon flash tube and associated lens reflector system The strobe must be with its weatherproof back box in order to remain outdoor approved per UL The strobe shall be suitable for use in wet environments Strobe Combination horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service The strobe shall be wired as a primary signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling flashing at 1 Hz over the strobe entire operating voltage range The strobe light shall consist of a xenon flash tube and associated lens reflector The horn shall have three audibility options and an option to switch between a temporal three pattern and a non temporal continuous pattern These shall be set by a multiple position switch On four wire products the strobe shall be powered independently of the sounder The horn or horn strobe shall operate on a coded or non coded power supply The horn strobe must be installed with its weatherproof back box in order to remain outdoor per UL The horn strobe shall be suitable for use in wet environments Specifications Temperature Flash Rate Voltage Voltage Range2 Terminal Wire Gauge Dimensions including lens Dimensions including lens Dimensions Weatherproof Back Box Dimensions SA WBB Weatherproof Back Box Dimensions SA WBBC Full Wave Rectified FWR voltage is a non regulated time varying power source that is used on some power supply and panel outputs P S PC and SC products will operate at 12 V nominal only for 15 and 15 75 cd to 151 to 66 flash per second 12 DC FWR or regulated 24 DC FWR1 to 17.5 V 12 V nominal or 16 to 33 V 24 V nominal to 18 AWG diameter 2.5 high 173 mm diameter 64 mm high L 4.7 W 2.5 D 142 mm L 119 mm W 64 mm D L 4.7 W 1.3 D 142 mm L 119 mm W 33 mm D L 5.1 W 2.0 D 145 mm L 130 mm W 51 mm D diameter 2.0 high 180 mm diameter 51 mm high Current Draw Data Max Strobe Current Draw mA RMS Range Range Volts Volts Max Horn Current Draw mA RMS Pattern Volts Volts Max Current Draw mA RMS 2 Wire Horn Strobe Standard Candela Range 15 cd Volts Volts Input High Medium Low High Medium Low Input High Medium Low High Medium Low Max Current Draw mA RMS 2 Wire Horn Strobe High Candela Range 135 cd Input High Medium Low High Medium Low Volts Input High Medium Low High Medium Low Volts not use below 32 rating at Derating K series products used at low temperatures listed candela must be reduced in accordance with this table Output cd Candela Tones and Sound Output Data and Horn Strobe Output dBA