System Sensor SENS-RDR Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS Reader Specifications Temperature Range Temperature Range without batteries Humidity Range USING SENS RDR sensitivity reader is a tool to measure the of i3 smoke detectors as well as 100 series con smoke detectors only models 2151 and 2151T after April 2006 It CANNOT be used on the 300 400 500 or 800 Series detectors This manual shall be left with the owner user of equipment Use of the SENS RDR is designed to each smoke detector is within its listed and marked range per NFPA 72 The SENS RDR CANNOT initiate a detector sensor alarm Sensitivity testing not be used as a substitute for smoke entry testing DESCRIPTION battery powered device is equipped with an infrared interface for reading data automatically sent by the detector every ten seconds The SENS RDR decodes sensitivity and status data and displays the informa on its LCD display SENS RDR may be used either as a hand held device with a standard threaded extension pole OPERATION Turn the reader on by pressing and holding the button approximately 2 seconds until the reader sounds LCD will display the word The indicates that the SENS RDR is ready for accept data from an i3 Series smoke detector Place the reader by the smoke detector being tested Posi the reader at an angle on the oval area or at the cham opening by the word See Figures 1 and 2 ledge and an anti skid tip is provided on the reader to the reader in place while it reads the sensitivity Hold the reader in this position up to 10 seconds until reader sounds and the reader red LED illuminates NOTE If the reader does not sound after 10 seconds that the reader is properly positioned and the displays The LED and sounder indicate a valid reading is re The reader will automatically display two The first is a percent per foot obscuration mea which is displayed for approximately 3 sec Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 to 120 0 to 49 to 140 to 60 to 90 RH non condensing followed by a textual status indication See Table The reader will continue to display both results for to 30 minutes or until the reader is reset 1 READER LOCATION ON COMPATIBLE SYSTEM SMOKE DETECTORS SENS RDR AN ANGLE ON THE AREA OR AT THE OPENING THE WORD 100 SERIES PLACE SENS RDR AT THE CIRCULAR NEAR WORDS NOT PAINT TEST SWITCH 2 POSITION READER ON COMPATIBLE SYSTEM SMOKE DETECTORS No further readings may be taken until the reader reset To measure the sensitivity of the next detector reset the by momentarily pressing the button The LCD again display the word Repeat steps 2 4 as necessary When finished turn off the reader by pressing and hold the button for approximately 2 seconds until the sounds 1 SENS RDR STATUS INDICATIONS Action DETECTOR IS WITHIN ITS SENSITIVITY NO ACTION IS NECESSARY AT THIS smoke detector sensing chamber requires for continued reliable operation Refer the i3 Series installation manual for proper procedures smoke detector is failing and should be immediately BATTERIES AND BATTERY LIFE SENS RDR operates with two AA alkaline batteries Other battery types may result in improper function the reader When the batteries in the SENS RDR get low the display will read BATT Once the low battery is reached the reader will no longer function batteries to restore operation to the SENS RDR SENS RDR automatically turns off when not used after minutes To conserve the battery life of the SENS RDR is recommended that the reader be turned off when not use To turn off the reader press and hold the button for 2 seconds until the reader sounds LIMITATIONS OF THE SENS RDR SENS RDR is designed to assure that each smoke detector is within its listed marked sensitivity range per NFPA 72 fluctuations in readings may be experienced on any device at any given time do not indicate a defect or sensitivity shift provided the reading is within the range These fluctuations are to be expected SENS RDR and its associated smoke detectors sensors contain electronic parts though they are designed to last over 10 years any of these components can fail any time Therefore it is recommended to test your smoke detectors sensors per 72 at least annually Regular cleaning and testing of your fire detection system measurably reduce your product liability risks and minimize nuisance alarms LIMITED WARRANTY Sensor warrants its enclosed product to be free from defects in and workmanship under normal use and service for a period three years from date of manufacture System Sensor makes no other warranty for the enclosed product No agent representative or employee of the Company has the authority to increase or alter obligations or limitations of this Warranty The Company obligation this Warranty shall be limited to the replacement of any part of the which is found to be defective in materials or workmanship under use and service during the three year period commencing with date of manufacture After phoning System Sensor toll free number 736 7672 for a Return Authorization number send defec units postage prepaid to Honeywell 12220 Rojas Drive Suite 700 El TX 79936 USA Please include a note describing the malfunction and cause of failure The Company shall not be obligated to replace which are found to be defective because of damage unreasonable modifications or alterations occurring after the date of manufacture no case shall the Company be liable for any consequential or incidental for breach of this or any other Warranty expressed or implied even if the loss or damage is caused by the Company or fault Some states do not allow the exclusion or limita of incidental or consequential damages so the above limitation or may not apply to you This Warranty gives you specific legal and you may also have other rights which vary from state to state STATEMENT device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device accept any interference received including interference that may cause undesired operation equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help System Sensor 06 10