Valcom PP+ Controller and Controller with Power Supply

PagePac 1 PLUS CONTROLLER (V-5323100) AND WITH POWER SUPPLY (V-5323105) PagePac Plus System consists of the Controller, and up to 3 Zone Expansion Units, providing to 56 paging and/or control zones. The self-powered comes with its own power supply, enabling it to paging and control zones utilizing a paging amplifier than the AmpliCenter. 16.0 x 1.8 x 6.9 x 4.5cm x 17.5cm) lbs. (0.9 kg) 8 Zones Paging or Control Contact Closure Inputs or Outputs Loop Start, Ground Start, CO Port, Analog Station Dry Loop Access Controller with Power Supply for Applications with Night Bell 7 Alert Tones Page Zone Groups Flexible Numbering Plan Amplified Speakers or Amplifiers other than PagePac Mount the PagePac Plus Controller and Zone Expansion Units, if any, to either a wall Figure 1), cabinet or a rack (below the AmpliCenter or other amplifier) (see Figure 2). When installing the PagePac Plus Controller, leave at least four inches of space above and below proper ventilation. the paging equipment in a ventilated room where there is easy access to speaker cabling (prefer- in the telephone equipment room). Manuals Online! – Manuals Online! – 1. Wall Mounted Hardware 2. Rack Mounted Hardware Connect background music input wires to Left and Right terminals if stereo, or, Left and Ground if not. Figure 3. The optional audio source can be a CD or tape player, AM, FM, or commercial radio, or other device. Manuals Online! – Manuals Online! – more than one AmpliCenter is used in the paging system, each one can be connected to the same source, or different audio device, if desired. 3. Music Input Connections on AmpliCenter Plug modular cord into connectors Amp on Controller and In on AmpliCenter Figure 4). If an amplifier other than the AmpliCenter is used, refer to page 10. There you will find wiring dia- and notes. 4. Page In Connection from Controller to AmpliCenter Connect 8-pin Molex connector from AmpliCenter to Controller (see Figure 5). Connectors can only go in one way. DO NOT force in. you are using another type of amplifier, refer to the example system setups. Manuals Online! – Manuals Online! – 5. 8-pin Molex Connector from AmpliCenter to Controller to Controller will occur if the Molex connector (from AmpliCenter) is into the right connector (This goes to Zone Expansion Units). Set the AmpliCenter Telephone Mode Selection Switch to Dry Loop 600 Ohms (Far left setting). Figure 6. 6. AmpliCenter Mode Switch Setting Connect 8-pin Molex from Controller to Zone Expansion Unit(s), if used. See Figure 7. Up to 3 Zone Expansion Units can be used, providing up to 56 paging and/or control zones. 7. 8-pin Molex Connector from Controller to Zone Expansion Unit(s) Manuals Online! – Manuals Online! – Set DIP switches on each Zone Expansion Unit, if any. See Figure 8. These DIP switches must be set correctly in order for the Controller to recognize the additional 8. Setting Zone Expansion Unit DIP Switches Using a small standard screwdriver, make the following adjustments: Adjust the Low Frequency Cut Off control to center position. This control cuts out the low fre- bass so that horns and small speakers are not over-driven and distorted by excessive energy. Cut-off frequency is continuously adjustable from 50Hz (full CCW rotation) to 400 Hz CW rotation). See Figure 9. Adjust the Page VOX (voice activated) sensitivity to the fully counterclockwise position. Adjust Music Input level to the center position. Clockwise rotation will increase the level. Listen set to a comfortable level. Adjust Music Ducking level to the fully counterclockwise position. This feature allows music to to be heard during a page, but at a reduced level. The range is less than dB (full to dB (full CW). If music is not connected, set to full CCW. 9. Sound Level Adjustments on AmpliCenter Manuals Online! – Manua