Valcom v-1134

VSP-V-1134 7 CALL ONE-WAY PAGE UNIT instructions provide the specifications and necessary to install, operate, and maintain V-1134, All Call One-Way Page Unit. provide one-way all call page to 34 zones when with the V-136RTHF 36 zone page control unit. V-136RTHF 36 zone handsfree control unit One-way all call amplification to 34 zones Dial 0 for all call Automatic release of all call unit with two off hook Easy installation – 30″ plug ended cable provided Built-in volume control for all call level Unit replaces stations 0 and 39 on 36 zone units. x 5.75″W x 2.13″D H x 14.61cm W x 5.41cm D) lbs. (1.8 kg) Requirements Vdc B battery 1 amp maximum milliwatts per speaker unit provides one-way all call page to the The functions and operation of the unit remain the same as without the all call with exception that dialing “0” energizes the all unit and permits a one-way page to all stations of intercom. precautions have been taken at the factory to insure the equipment functions properly. To insure operation and to prevent equipment damage, observe the following: Unplug the power supply before connecting any or cables to the control unit connecting Do not locate the control unit more than 5 feet the power supply or closer than 18 inches. Do not use a lamp tester to check signals, use a A lamp tester when first applied is a circuit to electronic circuits. Do not apply power to the control unit until all have been double-checked. Manuals Online! – the V-1134 close to the V-136RTHF control allowing enough room for the amphenol NOTE: The cable supplied with the unit is long. If units are separated by more than 30″, cable may be required. In a mixed system of Bell/Buzzer and signaling, stations 30-29, 0, and 5-9 be voice signaling. Bells or buzzers be connected as excluded speakers Figure 2). In a new installation, complete all steps of the installation procedure as shown in the instruct- ions for the V-136RTHF, combination. Connect the 25 pair intercom cable from the 66 type split block to the amphenol on the V-1134 marked “to 66 block.” In an existing system without all call, remove the intercom cable from the V-136RTHF and plug it into the amphenol on the V-1134 marked “to 66 block.” If all speakers are to receive all call, refer to Figure 1. One end of the 30″ cable supplied with the V-1134 should be plugged into the amphenol marked “to intercom.” The other end should plug into the V-136RTHF intercom unit. If some stations are to be excluded from the all call, refer to Figure 2. Punch down two 25 pair female amphenol ended cables on a 66 type solid block. Plug one cable to the V-1134 “to intercom” amphenol and plug the second cable to the V-136RTHF. Connect excluded speakers to the appropriate ICM number on the solid block and to the common speaker return on the split block. Connect non-excluded speakers as shown in the V-136RTHF installation instruction. Do not connect speakers to stations 0 39. Connections If using the V-1134 with the V-136RTHF, perform the following: Strap the Y/BN to the G/V on the “to 66 block” pair cable. Connections V-1134 requires no external power connections as power is derived from the power supplied to V-136RTHF. Care should be taken to make sure the power supply is capable of supplying the current requirements when the V-1134 is in the calling party goes off hook on the intercom dials “0”, the intercom switching network closes a for station “0”. This contact connects a ground supplied by the Y/BN lead of the (ICM connector) back to the O/V lead of the (ICM connector). The V-1134 operates a of relays with transfer contacts and all stations transferred to the outputs of audio amplifiers. After 1 second the amplifiers are energized the calling party can make a one-way page to all If station “0” is not dialed, the V-136RTHF perform in the manner de