Valcom P-Tec Speakers70v

PagePac VOICE PAGING SPEAKERS VOICE COIL 70 VOLT 2 Voice Paging Speakers are suitable for paging as well as background music The is a 70 volt model with adjustable taps volume control The V 5330100 is a voice coil Ohm 3.4 volt model with volume control speakers consist of a 3.6 inch cone mounted in a unique surface mount baf The baffle is designed for mounting on tile such as those normally found in sus and can be mounted without large holes in the tile The mounting pins be removed for mounting in a hard ceiling speaker housing has screw holes for securing without mounting pins Although the speakers are designed especially for stan suspended ceilings they can be used on types of ceiling materials 8 x 2.5 20.32cm x 6.35cm Coil 75 lbs 34 kg Volt 1.25 lbs 56 kg the Power Tap Wire 70V For the V 5330100 Speakers Voice Coil begin at Suspended Ceiling Installation Remove the Quick Connect connector from accessory pack Select the desired power tap wire 1 4W 1 2W 1W 2W 4W 1 P TEC Paging Speaker 70V shown the Quick Connect connector on the Use pliers to close the connector over wire The connector can be removed by it open with a screwdriver and can be several times see Figure 2 Box Optional Control Wire Refer to spacing chart Figure 6 for recom speaker spacing 2 Attaching the Reuseable Quick Connect Connector V 5330200 Only Manuals Online Manuals Online Connect the power tap wire to the gold see Figure 3 Arrange the unused power tap wires neatly the speaker housing and tape them to inside of the housing If necessary adjust paging volume after instal The volume control is located on the of the speaker Use a small screwdriver to the control Install the volume control cover found in the Silver pack When using a PagePac Amplicenter volume should be adjusted at the amplifier or music source Adjust before adjusting background music Speaker Phasing using multiple speakers in a single run speakers in phase by connecting the wires to the same spike on each speaker wire can connect on either spike as long the pattern is followed on each speaker The spike is the plus terminal see Figure 5 Next Paging 5 Maintaining Speaker Phasing Shielded Speaker Cable Only you are using shielded speaker cable splice the wire at the speaker location so a continu shield is maintained When connecting a sin speaker or the last speaker on the run clip shield wire where it emerges from the outer on the speaker cable ASSISTANCE calling have a VOM and a telephone test available and call from the job site Call 540 and ask for PagePac Technical Sup or call 540 427 6000 for Valcom 24 hour Support or visit our websites at and www valcom com Gold Transformer Common at Factory Tap Wires Tap Wires 1 4 Watt 1 2 Watt 1 Watt 2 Watt 4 Watt 1 4 Watt 1 2 Watt 1 Watt 2 Watt 4 Watt Wire unused wires inside speaker housing Figure 3 Connecting the Tap Wire V 5330200 Only Ceiling Wrap wires around strain relief posts so speaker wires will not pull free Lift the adjacent ceiling tile and slide it out of way Install the speaker by inserting the mounting through the ceiling tile and hold the in place Place the wire and washers and speaker clips over mounting pins so pins through clips mounting holes and screws spikes can not be used 4 P TEC Installation Washers provide isolation from the pins if back of the tile is covered with metal Manuals Online Manuals Online repairs be necessary attach a tag to the clearly stating company name address number contact person and the nature of problem Send the unit to Inc Repair Dept Hollins Road VA 24019 5056 SPEAKER PROJECTION DISTANCE PRESSURE LEVELS AND WATTAGE SETTINGS FOR 70 VOLT SPK WATT WATT WATT WATT WATT FT FT FT dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB SPEAKERS ARE INTENDED FOR USE IN STANDARD 8 FOOT DROPPED CEILING TILE HEIGHTS OF MORE THAN 8 FEET OR HIGHER NOISE LEVELS MAY REQUIRE LESS THE STANDARD 25 FOOT SPACING OR HIGHER TAP SETTINGS 6 Manuals Online Manuals Online