Valcom v-9940

VSP 9940 4 STATION LEVEL PAGE ADAPTER V 9940 is an Expandable Station Level Page designed to provide ring trip and page access for use on standard device telephone lines instructions contain the specifications and necessary to install operate and the V 9940 Expandable Station Level Page Please review dipswitch settings 3 for equipment suitability Information installing the V 9940 contact the local company and give them the following The telephone number of the line to which the will connect The FCC Registration BAF9I7 13957 OT N The ringer equivalence number 1.1A the V 9940 is disconnected from its present line the local telephone company to make them of the change Company Procedures The goal of the company is to provide the best service In order to do this it may occasionally be for them to make changes in their operations or procedures If these potentially affect the service or the operation customer equipment the telephone company will written notice to allow any changes necessary to uninterrupted service Methods Centrex numbers Loop start and ground start central office lines PABX station numbers 1 depicts a block diagram of a typical PABX Ring trip on first ring Ohm output 8 Ohm output with AGC Multiple units may be used for multi zone with all call behind a PABX Use with Valcom multi zone page control unit multi zone paging Centrex or C O lines signaling only Use with Valcom handsfree page units for paging Background music input Open loop detect reset Audio sensing circuit for reset Time out reset Manual reset Answer verification tone All call override tone Battery reversal indicator Auxiliary Make Break contact Built in 66 type connection block Complies with UL 145 Manuals Online used with a PABX the PABX must not return tones to the called party after calling party on a station to station call Each V 9940 provides one zone of paging when to its own PABX station number Use a V 9940 and a station number per zone for paging behind a PABX An additional station number and V 9940 may used to provide all call or override in a multi zone system behind a PABX One V 9940 may be used with a Valcom page unit to provide up to 36 zones paging on Centrex or central office lines signaling only x 4.55 x 2.3 D x 11.56cm x 5.84cm lbs 77 kg Requirements to 26 Vdc Battery 200 ma max Valcom VP 624B Class 2 power and Ring Input for ring trip to 50 Degrees C to 85 non precipitating Ohms Vac or 30 Hz Trip Timing Loop Detect Sense Release starting 1 after ring trip 8 16 32 or 64 after audio drops below 22dbm 4 8 16 32 or 64 seconds ground Out Release reset 1 ohms Level Output Level Input Level 1db Level Level Output Level 2 Level Level Source Verification Tone C Contacts Ohms to 600 Ohm to 18 dBm 250ms On Off Vdc 2.0 amps or Vac 1.0 amps Valcom V 9940 Expandable Station Level Page is designed to provide access to paging from standard PABX station number a Centrex number a Central Office line It should not be used on service lines or party lines The V 9940 may be connected to Valcom One Way Amplified assemblies or may be used in conjunction Valcom one zone or multi zone page adapters following sections describe possible and detail the equipment required One Way Amplified Speaker Assemblies are consult the Valcom catalog for the style Once the style and quantity of speakers are select the appropriate power supply after to the Valcom One Way Paging VSP or the Guide Station Level Paging Before proposing Station Level Paging the following test Dial between two stations on the PABX and the call Have the called party keep listening while the party hangs up After calling party release what does the called hear Manuals Online the PABX IMMEDIATELY returns any type of to the called party dial tone reorder tone etc STATION LEVEL PAGING CAN NOT BE Consult the Valcom catalog for an trunk level page adapter If there is of at least 10 SECONDS before any tones are then one way paging may be used If the REMAINS SILENT for at least 1 1 2 minutes disconnect then one way or talkback paging be used the type of paging desired is possible on a station of the PABX continue in this section to equipment required One Zone of One Way Paging arrangement requires one PABX station one V 9940 page adapter appropriate One Way Amplified Speaker Assemblies a 24 Vdc power supply Multi Zone One Way Paging with All Call arrangement requires a PABX station number V 9940 for each zone and an additional number V 9940 for all call One Way amplified Speaker and Vdc power supplies are also One Zone of Talkback Paging arrangement requires one V 9940 one one zone talkback unit appropriate 45 talkback speakers max 2 and a VP 624B supply See Note or C O Line Access to Although the V 9940 will work on both loop or ground start lines when using Centrex ground start lines provide better security returned tones In addition Centrex lines be optioned for cut OFF when disconnect One Zone of One Way Paging zone of One Way Paging requires one Centrex C O Line a V 9940 One Way Amplified Assemblies and a Vdc power supply Multi Zone One Way Paging One Way Paging requires one Centrex or Line a V 9940 a dial select page control unit V 2006A V 1109RTVA V 119RTVA V 136RTHF appropriate One Way Amplified Assemblies and a Vdc power supply All Call is included with the V 2003A and the V 1109RTVA may be added to the V 119RTVA with a V 1118 to the V 136RTHF with a V 1134 See Note One Zone of Talkback Paging Zone of Talkback Paging requires one Centrex C O Line one V 9940 one V 9941A one zone unit 45 ohm talkback speakers max 2 a VP 624B power supply See Note Multi Zone Talkback Paging Talkback Paging requires one Centrex or Line one V 9940 a dial select page control unit V 2006AHF V 1109RTHF