Valcom v-9943a

VSP V 9943A 3 MULTI TONE RINGER V 9943A is a Line Powered Electronic Multi Tone which is designed for use in an office with a quiet to moderate ambient noise The V 9943A can be connected to a C O Line Station or common audible contact to provide selectable tone and an LED indication to indicate the of incoming calls V 9943A has received FCC Registration Number and has a ringer equivalency of The unit is designed to be used with FCC Telephone Systems and installations may be by Valcom Inc equipment manufacturers companies registered telephone refurbishers those qualified for installation of FCC registered under FCC Rules Section 68.215 accordance with FCC Rules with applicable tariffs Ringer may only be installed with the authorization the owner of the host system FCC Registration Number will be listed in the filed with the telephone company it will also recorded in the system log kept by installation and personnel The local telephone company to be notified of the FCC Registration Number when Unit is installed RJ11C jack is required for direct interconnection the telephone network E Key system common audible ringer 1A2 key system common audible ringer PABX station ringer C O line extension ringer V 9943A is designed to give incoming call Incoming call indication is recognized as an tone and a light The tone can be a solid or tone Different frequencies can be selected using switches See Option Switch Chart a tone indication when a call is ringing in selectable tone s Volume control LED indication of incoming call power supply not required terminals for all connections x 5.65 x 1.75 x 14.35cm x 4.44cm lbs 23 kg Requirements Vac 20 30 Hz 50 mA max or Vdc 50 max Manuals Online 2 1 2 3 and 4 set the tones Refer to Option Switch Chart to obtain the setting the desired tone S y s tem t ure A C Ring V oltage an as s igned tation port on a A B X 1A 2 m on audible a Central O ffice 1 2 witc h 5 us t be in O N ition O R 1 2 witc h 5 us t be in O FF ition V 9943A is activated by 70 105 Vac ring voltage 24 Vdc normally through an interrupted contact If the V 9943A is to be connected to the network two wires should be secured to the terminal connection on the PCB The other end the wires should terminate at a RJ11C jack LED provides a visual indication when the unit is tones are dipswitch selectable The various tones are described in the Option Switch Chart with the switch configuration necessary to obtain tone dip switches and volume control are accessed the opening in the rear of the enclosure the Dip Switches 1 4 determine tone Switch 5 determines AC DC operation Determine if the equipment will be used with or DC current For DC current SW5 be in the ON position For AC current voltage SW5 should be in the OFF Do Not Use Ring Voltage with SW5 the ON position Switch the Volume Control volume control is screwdriver adjustable During setup it is recommended the volume control be 1 4 turn clockwise V 9943A has mounting holes located on the sides the unit Two 10 x 3 4 wood screws are included mounting purposes ASSISTANCE in troubleshooting is available from the When calling you should have a Volt ohm and a telephone test set available and be calling the job site Call 540 427 3900 and ask for Support or call 540 427 6000 for Valcom Automated Support or visit our website at equipment is not field repairable Valcom Inc service facilities in Roanoke VA Should be necessary attach a tag to the unit clearly your company name address phone number person and the nature of the problem Send the to Inc and Return Dept Hollins Road VA 24019 5056 Manuals Online SWITCH CHART SELECTION No Sound Low Pitch Solid Tone Low Pitch Warble Tone Low Pitch Fast Warble Tone Low Pitch Very Fast Warble Tone High Pitch Solid Tone High Pitch Warble Tone High Pitch Fast Warble Tone High Pitch Very Fast Warble Tone Very High Pitch Solid Tone Very High Pitch Warble Tone Very High Pitch Fast Warble Tone Very High Pitch Very Fast Warble Tone V 9943A can be used as a contact closure with dip switch 5 ON ring voltage dipswitch 5 should be in the OFF position Dip switch positioned Up OFF Dip switch positioned Down ON LIMITED WARRANTY Inc warrants its products to be free from defects in materials and workmanship under conditions of normal use and service a period of one year from the date of shipment The obligation under this warranty shall be limited to the replacement repair or of any such defective device within the warranty period provided that 1 2 3 by Valcom Inc indicates the validity of the claim defect is not the result of damage misuse or negligence after the original shipment product has not been altered in any way or repaired by others and that factory sealed units are unopened service charge plus parts and labor will be applied to units defaced or physically damaged charges for the return of products to Valcom are prepaid units of warranty are subject to a service charge The service charge will cover minor repairs repairs will be subject to additional charges for parts and labor 4 5 warranty is in lieu of and excludes all other warranties expressed or implied and in no event shall Valcom Inc be for any anticipated profits consequential damages loss of time or other losses incurred by the buyer in connection the purchase operation or use of the product warranty specifically excludes damage incurred in shipment In the event a product is received in damaged condition the carrier be notified immediately Claims for such damage should be filed with the carrier involved in accordance with the F O B point Inc Industry Avenue VA 24013 540 427 3900 540 427 3517 Canada Corporation Van Kirk Drive 11 and 12 Ontario L7A1A5 905 456 1072 905 456 2269 Manuals Online