Valcom v-9947a

VSP V 9947A 8 POWERED LOUD RINGER HORN V 9947A is a Line Powered Loud Ringer Horn provides amplified electronic tones for signalling large or noisy areas This instruction contains the and information necessary to install and maintain the V 9947A equipment has received FCC type KX registration and has a REN of 2.7A The FCC Registration BAF9I7 19317 RG N will be listed in the filed with the telephone company it will also recorded in the system log kept by installation and personnel The local telephone company to be notified of the FCC Registration Number when equipment is installed V 9947A is a ringer horn containing circuitry to incoming call indication via a warble or single when activated by 70 120 Vac ring voltage Equivalency Number 2.7A plan a system utilizing the V 9947A refer to the Distance Chart to determine approximate covered The number given ft is the side to distance for mounting the speakers It is also the in front of the speaker that a good quality can be heard C O audible ringing Loud ring Omni directional mounting bracket Self contained tone generator amplifier volume and horn speaker Single or warble tone output Activated by 70 120 Vac ring voltage Tones continuous for duration of ring cycle Weatherproof Units may be multipled for simultaneous access Separate power supply not required x 8.2 W x 10.4 D plus mounting bracket H x 20.83cm W x 26.42cm D lbs 1.5 kg Requirements Hz 35 mA maximum however the V is line driven and a separate power supply not required Temperature Humidity to 55 degrees C non precipitating Manuals Online Connections the tip green and ring red leads of the ringer the corresponding leads of the telephone the ringer is be used in conjunction with To produce a warble tone the black and white remain unconnected To produce a single tone connect the black and leads to each other See Figure 3 Speaker to Base speaker may be attached to the base before or after base is mounted Loosen position adjustment knob the ball of the base into the socket of the Tighten the position adjustment knob V 9947A should be mounted 12 to 25 high to optimum results This ringer may be used for interior or exterior signalling applications Mount the base to a wall using the two holes Knockout holes are provided for punch should additional holes be desired A C clamp is provided with the ringer to allow to a beam Place the bolt through the in the bottom of the base to secure the C to the beam See Figure 1 It is suggested the horn be mounted to the underside of the I so as to provide the maximum of positioning Connection backbox by channeling wire through the ball the base and making appropriate connections base has holes punched for a double gang box but by punching out additional holes the base can be mounted to a or octagon box See Figure 2 V 9947A may be rotated or moved up and down to the desired position by loosening the position knob at the bottom of the unit See Figures and 2 approximately 1 turn Make required and re tighten the knob ASSISTANCE trouble is reported verify there are no broken between the telephone and the ringer volume control is turned up in troubleshooting is available from the When calling you should have a VOM and a set available and be calling from the job site Call 427 3900 and ask for Technical Support or call 427 6000 for Valcom 24 hour Automated or visit our website at http www valcom com equipment is not field repairable Valcom Inc service facilities in Roanoke VA Should be necessary attach a tag to the unit clearly company name address phone number contact and the nature of the problem Send the unit to Inc and Return Dept Hollins Road VA 24019 5056 DISTANCE CHART Noise Level dB 100 110 120 ft Spacing in Feet Manuals Online Clamp Base 1 Mounting to a Beam with a C Clamp 2 Mounting to an Electrical Backbox Manuals Online Inc warrants its products to be free from defects in materials and workmanship under conditions of normal use and service for period of one year from the date of shipment The obligation under this warranty shall be limited to the replacement repair or refund any such defective device within the warranty period provided that LIMITED WARRANTY 1 2 3 4 5 by Valcom Inc indicates the validity of the claim defect is not the result of damage misuse or negligence after the original shipment product has not been altered in any way or repaired by others and that factory sealed units are unopened service charge plus parts and labor will be applied to units defaced or physically damaged charges for the return of products to Valcom are prepaid units of warranty are subject to a service charge The service charge will cover minor repairs repairs will be subject to additional charges for parts and labor warranty is in lieu of and excludes all other warranties expressed or implied and in no event shall Valcom Inc be liable any anticipated profits consequential damages loss of time or other losses incurred by the buyer in connection with the operation or use of the product warranty specifically excludes damage incurred in shipment In the event a product is received in damaged condition the carrier be notified immediately Claims for such damage should be filed with the carrier involved in accordance with the F O B point Inc Industry Avenue VA 24013 540 427 3900 540 427 3517 Canada Corporation Van Kirk Drive 11 and 12 Ontario L7A1A5 905 456 1072 905 456 2269 3 9947A C O Line A nalog tation P ort hite lac k t together to e s ingle tone arble tone is produced not c onnec ted Manuals Online