Wheelock MPS explosion-proof, pull station install sheet P84045

Branchport Avenue Branch N J 07740 631 2148 MPS 400X EXPLOSION PROOF FIRE ALARM PULL STATION you for using our products INSTRUCTIONS this product according to this instruction manual Please keep this instruction manual for future reference Listed By UL FM CSFM MEA Series MPS 400X Explosion Proof Manual Pull Station is UL and FM Listed for use in hazardous environments and for NEMA 4X weatherproof applications The unit also complies with ADA Standards when installed at less than 48 inches above the floor front wheelchair access and less than 54 inches for side wheelchair access All installations must comply with local codes and Class I Groups B C and D Class II Groups E F and G Class III D P D T 10 Amps at 250VAC 1 2 Amp at 125VDC also refer to assembly diagram and installation notes Series MPS 400X station includes a front housing backbox a switch plate and all the necessary hardware to assemble the station the backbox onto its mounting surface using the holes provided on the mounting tabs The tabs are designed to accept a size of up to 1 4 inch The backbox is supplied with two 3 4 inch 14 NPT conduit entries Threaded joints between conduit and backbox must be made a minimum of 5 threads fully engaged Seal unused conduit entry with a 3 4 inch NPT pipe plug All joints must be sealed pipe thread sealing compound or Teflon tape and in accordance with the requirements for the particular installation Connect the field wiring to the terminal blocks on the adapter plate Use the insulated terminal plug supplied to ground the box Each wire or terminal lug must be placed under its corresponding clamping plate for proper connection the switch plate onto the backbox using the 4 1 4 20 X 7 8 pan head screws provided Make sure that the O Ring seals on screws and around the edge of the switch plate are properly seated Open the front housing align its mounting plate with the pins provided on the switch plate and attach it using the two 6 32 screws into the slot holes 2009 Cooper Wheelock Inc dba Cooper Notification All rights reserved B 1 of 3 DIAGRAM SCREW FRONT HOUSING SWITCH PLATE BACK BOX Check make sure flange surfaces are clean and free of scratches debris and dust Verify that the O Rings seals on the 4 7 8 screws and the around the inside surface of the switch plate are seated Seal unused conduit entry with a 3 4 inch NPT plug Connect the ground wire to the grounding screw in the After tightening the 4 switch plate bolts verify that a feeler gauge does not penetrate more than at any point around the flange joint SUPPLIED SCREWS O RING SEALS ONLY Block Layout IN THE UPRIGHT POSITION B 2 of 3 CAUTION Before beginning verify that the supply is turned off Take care not to scratch or damage the surfaces of the flange WARRANTY Wheelock Inc dba Cooper Notification and Cooper Notification Inc each a products must be used within their specifications and must be PROPERLY specified applied installed operated maintained and operationally tested in with these instructions at the time of installation and at least twice a year or more often and in accordance with local state federal codes regulations and laws Specification application installation operation maintenance and testing must be performed qualified personnel for proper operation in accordance with all of the latest National Fire Protection Association NFPA Laboratories UL National Electrical Code NEC Occupational Safety and Health Administration OSHA local county province district federal and other applicable building and fire standards guidelines regulations laws and codes but not limited to all appendices and amendments and the requirements of the local authority having jurisdiction AHJ products when properly specified applied installed operated maintained and operationally tested as provided above are against mechanical and electrical defects for a period of a three 3 years from date of manufacture with respect to MEDC Seller Industrial Signals and Seller Fire and Security Notification Appliances and Devices or b one 1 year from date of with respect to Waves and SafePath Voice Evacuation and Mass Notification Systems date of manufacture is determined date code Correction of defects by repair or replacement shall be at Seller sole discretion and shall constitute fulfillment of all under this warranty THE FOREGOING LIMITED WARRANTY SHALL IMMEDIATELY TERMINATE IN THE ANY PART NOT FURNISHED BY SELLER IS INSTALLED IN THE PRODUCT THE FOREGOING LIMITED SPECIFICALLY EXCLUDES ANY SOFTWARE REQUIRED FOR THE OPERATION OF OR INCLUDED IN A SELLER MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND EXPRESS IMPLIED OR WHETHER AS TO MECHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER OR WHETHER IT WILL ACHIEVE THE USER INTENDED RESULTS THERE IS NO WARRANTY AGAINST RESULTING FROM MISAPPLIACATION IMPROPER SPECIFICATION ABUSE ACCIDENT OR OTHER CONDITIONS BEYOND SELLER CONTROL DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR OR THAT THE SOFTWARE WILL MEET ANY OTHER STANDARD OF PERFORMANCE OR THAT THE OR PERFORMANCE OF THE SOFTWARE WILL MEET THE USER REQUIREMENTS SELLER SHALL BE LIABLE FOR ANY DELAYS BREAKDOWNS INTERRUPTIONS LOSS DESTRUCTION ALTERATION OR PROBLEMS IN THE USE OF A PRODUCT ARISING OUT OF OR CAUSED BY THE SOFTWARE LIABILITY OF SELLER ARISING OUT OF THE SUPPLYING OF A PRODUCT OR ITS USE WHETHER ON NEGLIGENCE OR OTHERWISE SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING AS STATED IN THE LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL LIABILITY SHALL TERMINATE SELLER IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL OR REPAIR OF A PRODUCT BY ANYONE OTHER THAN SELLER OR FOR DAMAGE OF ANY TYPE INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT OR INCIDENTAL INDIRECT CONSEQUENTIAL PUNTIVE OR EXEMPLARY DAMAGES THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE AND THE EXCLUSIVE LIABILITY OF SELLER NO CASE WILL SELLER LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT OF LIABILITY LIABILITY ON ANY CLAIM OF ANY KIND INCLUDING NEGLIGENCE AND BREACH OF WARRNTY FOR LOSS OR DAMAGE RESULTING FROM ARISING OUT OF OR CONNECTED WITH THIS CONTRACT OR FROM MANUFACTURE SALE DELIVERY RESALE REPAIR OR USE OF ANY PRODUCT COVERED BY THIS ORDER BE LIMITED TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE TO THE SELLER LIABILITY ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE IN THE PRODUCT OF ANY PART NOT FURNISHED BY SELLER IN NO EVENT SHALL SELLER BE FOR ANY CLAIM OF ANY KIND UNLESS IT IS PROVEN THAT ITS PRODUCT WAS THE DIRECT CAUSE OF CLAIM FURTHER IN NO EVENT INCLUDING IN THE CASE OF A CLAIM OF NEGLIGENCE SHALL SELLER BE FOR INCIDENTAL INDIRECT CONSEQUENTIAL SPECIAL PUNITIVE OR EXEMPLARY DAMAGES SOME DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO PRECEDING LIMITATION MAY NOT APPLY TO ALL PURCHASERS B 3 of 3