Wheelock MPS pull station install sheet P84044

Branchport Avenue Branch N J 07740 631 2148 SERIES MPS FIRE ALARM PULL STATION Thank you for using our products INSTRUCTIONS this product according to this instruction manual Please keep this instruction manual for future reference Series MPS Pull Station may be surface mounted indoors with a separately ordered backbox option or flush mounted on a single gang switch plate In either case be sure to follow local codes and regulations To comply with ADA standards the Station must be less than 48 inches above the floor for front wheelchair access and less than 54 inches above the floor for side access MPS Pull Stations when mounted to the Series MPS WP Backbox with Gasket Assembly are listed for outdoor and are NEMA 3R listed DIMENSIONS 4 x 3 x 2 MOUNT surface mount installation uses a red diecast MPS WB or sheet metal MPS ISB Backbox The backbox has four pre drilled holes of 0.187 inch diameter A screw size of 8 or smaller can be used to attach the backbox to a wall After the backbox is place attach the conduit The diecast backbox MPS WB has an opening that is tapped for a 1 2 inch NPT fitting which may be at the top or bottom when the box is attached to the wall The sheet metal backbox MPS ISB has conduit knockouts Field is connected to a terminal block as shown in the wiring drawings The wiring should not be wrapped around the terminal but under the clamping plate The housing is locked using a keylock Unlock the housing by turning the key clockwise and swing the front of the housing to make the sheet metal mounting plate accessible Mount the metal plate to the backbox using the four inch length 8 32 screws that are supplied If a Breakrod MPS RODS is being used move the PULL handle to about a 45 angle with the face of the housing Insert a breakrod into the cavity beneath the PULL handle Place the PULL handle back the normal position flush with the housing While holding the PULL handle in place move the housing back to the upright and lock The Pull Station in now ready for operation MOUNT flush mount installations may be attached to a standard single gang switch box not supplied The only difference between a mount installation and flush mount installation is that the two 6 32 screws are placed through the slots that are centered on the plate DRAWINGS 1 MPS 100 200 2 MPS 300 SCREW NEXT DEVICE EOLR FACP Alarm Circuit FIRE ALARM PANEL RATINGS 30 VDC 1 amp 120 VAC 1 amp 2009 Cooper Wheelock Inc dba Cooper Notification All rights reserved SCREW next EOLR next EOLR E 1 of 2 WARRANTY Wheelock Inc dba Cooper Notification and Cooper Notification Inc each a products must be used within their specifications and must be PROPERLY specified applied installed operated maintained and operationally tested in with these instructions at the time of installation and at least twice a year or more often and in accordance with local state federal codes regulations and laws Specification application installation operation maintenance and testing must be performed qualified personnel for proper operation in accordance with all of the latest National Fire Protection Association NFPA Laboratories UL National Electrical Code NEC Occupational Safety and Health Administration OSHA local county province district federal and other applicable building and fire standards guidelines regulations laws and codes but not limited to all appendices and amendments and the requirements of the local authority having jurisdiction AHJ products when properly specified applied installed operated maintained and operationally tested as provided above are against mechanical and electrical defects for a period of a three 3 years from date of manufacture with respect to MEDC Seller Industrial Signals and Seller Fire and Security Notification Appliances and Devices or b one 1 year from date of with respect to Waves and SafePath Voice Evacuation and Mass Notification Systems date of manufacture is determined date code Correction of defects by repair or replacement shall be at Seller sole discretion and shall constitute fulfillment of all under this warranty THE FOREGOING LIMITED WARRANTY SHALL IMMEDIATELY TERMINATE IN THE ANY PART NOT FURNISHED BY SELLER IS INSTALLED IN THE PRODUCT THE FOREGOING LIMITED SPECIFICALLY EXCLUDES ANY SOFTWARE REQUIRED FOR THE OPERATION OF OR INCLUDED IN A SELLER MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND EXPRESS IMPLIED OR WHETHER AS TO MECHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER OR WHETHER IT WILL ACHIEVE THE USER INTENDED RESULTS THERE IS NO WARRANTY AGAINST RESULTING FROM MISAPPLIACATION IMPROPER SPECIFICATION ABUSE ACCIDENT OR OTHER CONDITIONS BEYOND SELLER CONTROL DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR OR THAT THE SOFTWARE WILL MEET ANY OTHER STANDARD OF PERFORMANCE OR THAT THE OR PERFORMANCE OF THE SOFTWARE WILL MEET THE USER REQUIREMENTS SELLER SHALL BE LIABLE FOR ANY DELAYS BREAKDOWNS INTERRUPTIONS LOSS DESTRUCTION ALTERATION OR PROBLEMS IN THE USE OF A PRODUCT ARISING OUT OF OR CAUSED BY THE SOFTWARE LIABILITY OF SELLER ARISING OUT OF THE SUPPLYING OF A PRODUCT OR ITS USE WHETHER ON NEGLIGENCE OR OTHERWISE SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING AS STATED IN THE LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL LIABILITY SHALL TERMINATE SELLER IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL OR REPAIR OF A PRODUCT BY ANYONE OTHER THAN SELLER OR FOR DAMAGE OF ANY TYPE INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT OR INCIDENTAL INDIRECT CONSEQUENTIAL PUNTIVE OR EXEMPLARY DAMAGES THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE AND THE EXCLUSIVE LIABILITY OF SELLER NO CASE WILL SELLER LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT OF LIABILITY LIABILITY ON ANY CLAIM OF ANY KIND INCLUDING NEGLIGENCE AND BREACH OF WARRNTY FOR LOSS OR DAMAGE RESULTING FROM ARISING OUT OF OR CONNECTED WITH THIS CONTRACT OR FROM MANUFACTURE SALE DELIVERY RESALE REPAIR OR USE OF ANY PRODUCT COVERED BY THIS ORDER BE LIMITED TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE TO THE SELLER LIABILITY ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE IN THE PRODUCT OF ANY PART NOT FURNISHED BY SELLER IN NO EVENT SHALL SELLER BE FOR ANY CLAIM OF ANY KIND UNLESS IT IS PROVEN THAT ITS PRODUCT WAS THE DIRECT CAUSE OF CLAIM FURTHER IN NO EVENT INCLUDING IN THE CASE OF A CLAIM OF NEGLIGENCE SHALL SELLER BE FOR INCIDENTAL INDIRECT CONSEQUENTIAL SPECIAL PUNITIVE OR EXEMPLARY DAMAGES SOME DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO PRECEDING LIMITATION MAY NOT APPLY TO ALL PURCHASERS E 2 of 2