Wheelock Universal Telephone Alerts (UTAWH) install sheet P82969

Branchport Avenue Branch NJ 07740 631 2148 Thank you for using our products INSTALLATION INSTRUCTIONS TELEPHONE ALERT WITH STROBE this product according to this instruction manual Please keep this instruction manual for future reference UTA WH 115 VAC LINE CORD IS REQUIRED FOR STROBE AND PIEZO ACTIVATION THIS UNIT REQUIRES TWO SEPARATE VOLTAGE INPUTS TO OPERATE 115VAC 60Hz AND AN INPUT VOLTAGE LISTED TABLE 5 TO TRIGGER THE RINGING CIRCUIT INFORMATION UTA WH has a loud attention getting electronic ringer designed for use in noisy locations or for wide area coverage It is FCC Part 68 and IC Registered for the public telephone network and can be used behind PBX and key systems that use interrupted ring voltages from 40 130V or 20 30VDC VAC or 36 60VDC UTA WH when used indoors will accommodate a modular plug that mates with an RJ 11C jack USA or a CA 11 jack Canada for ringing The input voltage triggers the strobe and audible which receive their operating power from the 115VAC 60Hz source includes a high intensity flashing strobe for visual signaling and offers a choice of four selectable sound patterns horn bell single chime vibrating chime with a volume control The UTA WH is equipped with a weather resistant backbox for optional outdoor use with conduit wiring INFORMATION installation of this product must conform to the following instructions IF ANY WORDS OR LETTERS APPEAR ON THE PRODUCT A PARTICULAR USE THE PRODUCT MUST BE USED ONLY IN THE MANNER SO INDICATED FIELD ADJUSTMENT OR MODIFICATION OF THESE SIGNALS SHOULD NOT BE ATTEMPTED Malfunctioning units should be returned for factory or replacement in accordance with Cooper Notification published terms and conditions All CAUTIONS and WARNINGS are identified by the symbol All warnings are printed in bold capital letters The installation of this equipment should only be undertaken by qualified personnel THE UTA WH IS NOT TO BE USED AS AN INDOOR VISUAL EVACUATION SIGNAL FOR THE HEARING SHUT OFF ALL POWER BEFORE INSTALLING ELECTRICAL SHOCK CAN CAUSE DEATH OR SERIOUS equipment complies with Part 68 of the FCC Rules The label affixed to this product contains among other information the FCC Number and the Ringer Equivalence Number REN for this product This information must be provided to the telephone company requested REN is used to determine the quantity of appliances which you may connect to your telephone line and still have all of those appliances when your telephone number is called In most but not all areas the sum of the REN of all appliances connected to one line should not five 5.0 To be certain of the number of appliances that you may connect to your line contact your local telephone company equipment should not be used on coin telephone lines Connection to party line service is subject to state tariffs trouble is experienced disconnect this equipment from the telephone line to determine if it is causing the malfunction If the equipment is to be malfunctioning its use shall be discontinued until the problem has been corrected the equipment cause harm to the telephone network the telephone company shall if possible notify the customer that temporary of service may be required however where prior written notice is not possible the telephone company may temporarily service without notice if such action is necessary under the circumstances The telephone company may make changes in its facilities equipment and operations procedures where such action is reasonably required in the operation of its business and is inconsistent with the rules and regulations of the Federal Communications Commission 2009 Cooper Wheelock Inc dba Cooper Notification All rights reserved K 1 of 5 REGULATIONS CANADA REGULATIONS Only applicable for use in Canada NOTICE The Industry Canada IC label identifies certified equipment This certification means that the equipment meets certain network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical document s The Department does not guarantee the equipment will operate to the user satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic pipe system if present are connected together This precaution may be particularly Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or as appropriate RINGER EQUILAVENCE NUMBER The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the number of terminals allowed to be connected to a telephone interface The termination of an interface may consist of any combination devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 1 Sound Output dBA and Current REN at Maximum Volume Chime Chime Sound REN REN REN REN REN Input Voltage Range 24VDC 20 30VDC 24VAC 20 30VAC 48VDC 36 60VDC 90Vrms 40 130Vrms 20 30Hz For 24VDC 24VAC and 48VDC inputs add 10 more input current when operating the unit at maximum input voltage For 90Vrms inputs 40 more input current when operating the unit at maximum input voltage dBA is measured on axis in a non reflective free field test room using fast meter response 2 Sound Output Volume Adjusting Range Chime Chime Chime Chime 3 Tone Description Horn Modulated 0.07 Sec ON Repeat 1.0 Sec Decay Repeat 1.0 Sec Decay 48VDC 4 Duty and Ring Cycle Cycle Ring Cycle ON Time Ring Cycle OFF Time Ring Cycle ON Time Max Sec Sec Sec Max Sec Sec Flash Rate Nominal 1 Flash Minimum Ring Cycle Output 15cd on axis Current 0.150 Amps Max K 2 of 5 SETTINGS SW1 and SW2 switches of the UTA WH are used to set input voltage and desired tone as shown in Figure 2 and Table 5 The potentiometer shown in Figure 2 is used to adjust the volume of sound factory settings are Voltage 90Vrms 20 30Hz SW1 POS 1 set on 0 Horn SW2 POS 1,3,4 set on 1,1,1 P0S 2 set on 0 Maximum 5 Input Voltage and Tone Selections Chime Chime Sound Chime Chime Sound Settings 1 2 3 4 1 Any Setting INFORMATION UTA WH is designed for mounting to walls partitions or posts in both indoor and outdoor applications Refer to Figures 1,2 and 3 for wiring and adjustment of each model Use 4 conductor modular telephone line cord