Autocall InfoAlarm Command Center for Fire Alarm Control Panels with EPS Power Supplies

4100ES Fire Control Units Command Center for Fire Alarm Control Units with EPS Power Supplies ULC CSFM Listed NYC Fire Approved with Autocall ES Net Alarm Network expanded content display interface for Autocall 4100ES fire alarm control units available with the following Fire alarm control units stand alone or networked Network Display Units NDU with support for up to 12,000 points Remote InfoAlarm Command Centers mounted in a dedicated cabinet control units support Remote InfoAlarm Command Centers of host panel display type Models include an Enhanced Power Supply EPS and battery 9 A total with on board IDNAC SLCs signaling line circuit addressable appliance control an electrically isolated IDNet 2 device control module with dual short circuit isolating loops and programmable function auxiliary output For additional information concerning EPS power supplies and their features refer to 4100ES data sheet AC4100 0100 For additional 4100ES related applications including models with supplies for conventional non addressable NACS refer to data AC4100 0045 Command Centers provide customized operating Activity in System primary display choices include First and Most First 5 and Most Recent First 8 Site Plan with activity status General Alarm or Direct to List selectable individually by event System reports are easily viewed logs can be read with minimal required Up to six softkeys per screen provide functions that aid operators in how to proceed Up to two languages are available per system easily selected by key press systems with IMS GCC NPU or 2 x 40 LCD or annunciators require one language to be the default font International models allow customized language legends for operator and status LEDs Information sent to Remote InfoAlarm Command Centers can be by point properties 320 x 240 dot matrix QVGA display provides an active area of 4.53 W 3.4 H 115 mm x 86 mm Bright white LED backlighting provides efficient and long lasting operation is selectable as continuous or off with power fail with no key presses listed to Standard 864 1 Command for Control Unit Mounting 2 Command Center in Remote Cabinet more information 4100ES Controls using the InfoAlarm Center provide an expanded content multi line LCD interface requires minimal key presses to access detailed information it is system powered its detailed information is provided requiring separate supplementary equipment Command Center Control Unit By using a larger area instead of an individual text line display the LCD provides text for Alarm Supervisory or Trouble The format is flexible and to be customized per application allowing additional information to presented to suit the specific application Command Centers for 4100ES fire alarm systems provide large display with extended information content dual language including 2 byte character languages and an intuitive control interface per the following Up to 10 InfoAlarm Command Centers are supported per 4100ES unit able to allow one InfoAlarm Command Center to take and to designate access levels for interfaces not in control can be programmed for in control status indications Menu driven format conveniently prompts operators for the next required Key controls are provided to select the highlighted entry load next of information or jump to top or bottom of activity lists Direct point callup displays individual points alphabetically and then in on the logical choice as more point information is entered A Site Plan bitmap can be displayed for reference icons can be added indicate system status Up to 50 custom point detail messages can be generated Date formats are either MM DD YY or DD MM YY Time formats are either 24 hour or 12 hour with AM PM System Normal screen supports a gray scale bitmap watermark for name company logo or site plan This product has been approved by the California State Fire Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety Code See CSFM Listings 7120 2269 0546 7120 2269 0547 7165 2269 0542 for allowable values and or conditions concerning material presented in this document NYC Fire Dept COA 6271A Additional listings may be applicable contact your local supplier for the latest status Rev 11 1 2020 documentfirealarmresources com Command Center for Fire Alarm Control Units with EPS Power Supplies Plan with Event Icons Plan BitmapThe InfoAlarm Command Center supports a site plan bitmap image size is 281 pixels wide by 192 pixels high can also display icons indicating activity and location Figure 3 shows a site plan with icons shown in each building area For this example area is showing an A for an initiating device in alarm a WF for occurring and an icon indicating notification appliances in Icons can be created for site specific symbology these are for only Plan Selection and Detail If desired the site plan can be the display screen for system activity or can be for reference available selecting the Site softkey Depending on the facility layout the site can also be a convenient location for common reference information as primary call phone numbers street address etc to assist in their assigned response Normal Screen The site plan or another bitmap image can displayed on the System Normal screen as a grey image watermark the screen text Size and type are the same as that for a site plan This can be used to identify the specific location of the 4100ES or display a site specific logo or other information Review 4 Review Emphasis Main Menu screen illustration shown in Figure 5 demonstrates how statements appear for status information or for prompting user input Other examples of this format occur when setting time and entering a password or identification of a status change such as enabling or disabling Use of this feature allows the display to clearly the user on required information or actions 3 Plan Bitmap Trouble Log History screen shown in Figure 4 identifies the ability to multiple event entries with minimal scrolling For specific information pressing Next or Previous on the keypad highlights the selected or previous item in the list as indicated by the arrow and the bolded line of Entry 6 access to the next or previous full screen of information use the Page or Page Up keys located to the right of the soft keys each to the right the display 5 Emphasis 2 Rev 11 1 2020 documentfirealarmresources com Primary Display Screens 6 and Figure 7 are samples of a First and Most Recent primary display and of a General Alarm display Command Center for Fire Alarm Control Units with EPS Power Supplies 6 and Most Recent Primary Display Option 7 Alarm Primary Display Option 3 Rev 11 1 2020 documentfirealarmresources com Unit Operation Reference Command Center for Fire Alarm Control Units with EPS Power Supplies 4 Rev 11 1 2020 documentfirealarmresources com Feature Reference Command Center for Fire Alarm Control Units with EPS Power Supplies 5 Rev 11 1 2020 documentfirealarmresources com Display Details Command Center for Fire Alarm Control Units with EPS Power Supplies 6 Rev 11 1 2020 documentfirealarmresources com Command Center for Fire Alarm Control Units with EPS Power Supplies Selection Type Yes 1 4100ES Master Controller with InfoAlarm Command Center VAC Hz VAC Hz Command Center Type Controller Assembly raised keys with labels Controller Assembly flat keys with inserts custom key labels Controller Features CPU Module with RUI isolated un isolated communications interface A Enhanced Power Supply EPS with charger electrically isolated 250 IDNet 2 Module three Class B SLCs one 2 A output configurable Auxiliary Power or Simple NAC and expansion slot for City or Alarm Supv Tbl Relay option Please refer to data sheet AC4100 0100 for detailed descriptions of the 4100ES with EPS Basic Control Panel details standard product features and ref