Autocall QuickConnect2, TrueAlarm Analog Photoelectric Sensor

UL ULC CSFM Listed FM A4098 9757 QuickConnect2 sensor design provides TrueAlarm photoelectric analog sensing and IDNet two wire communications combined into one assembly Quick and easy connection to a A4098 9788 base required ordered Operation for ceiling or wall mounting Operation for use with Autocall models 4007ES 4010ES 4100ES with 2 and IDNet 2 2 Modules UL listed to Standard 268 sensors communicate to the control panel provide the following TrueAlert analog sensing operation Smoke sensitivity that is accurately maintained at the selected level by the control panel 4007ES 4010ES and compatible 4100ES 4100U Series control panels seven levels of sensitivity from 0.2 to 3.7 ft of obscuration to page 2 for application details Sensitivity monitoring that satisfies NFPA 72 sensitivity testing integrity Automatic environmental compensation Automatic once per minute individual sensor calibration check verifies Ability to display and print detailed sensor information in plain English Tracking of excessive dirt accumulation base provides stationary wiring terminals and quick sensor connections Mounting is on a 4 square 4 octagonal or single gang box supplied 4098 9832 Adapter Plate is available for retrofit and certain mounting refer to page 2 and architecturally styled chamber enclosure details Louvered design enhances smoke capture by directing flow to Entrance areas are minimally visible when ceiling mounted Chamber is easily accessible for cleaning Designed for EMI compatibility Internal magnetic test feature that activates alarm red LED with red lens indicates Power on when pulsing Alarm or Trouble when steady on a remote is not supported Refer to data sheet AC4098 0019 for sensor bases that support LED connections and additional TrueAlarm analog detection Analog Sensing TrueAlarm Analog Photoelectric Sensor 1 QuickConnect2 Sensor Mounted in A4098 9788 Base applications that only require basic TrueAlarm features the QuickConnect2 sensor provides addressable analog in a cost effective compact package The control panel monitors maintains the selected sensitivity of the A4098 9757 as well as automatic compensation for environmental conditions such as dirt and component degradation and TrueAlarm data capture for sensor Mounting connections are made to the A4098 9788 base which provides secure and quick connection for the A4098 9757 sensor Sensor and electronics are contained in the A4098 9757 sensor Alarm and Trouble LED Indication control panel also determines when individual sensors need Dirty sensors or other sensor troubles will automatically be at the control panel and that sensor LED will light steadily an alarm condition the alarmed sensor LED will light steadily LED is controlled by the panel During system alarm a sensor that was lit to indicate trouble will return to pulsing to conserve power as long as it is not in alarm Locations locations should be determined only after careful consideration the physical layout and contents of the area to be protected Refer NFPA 72 the National Fire Alarm and Signaling Code On smooth spacing of 30 ft 9.1 m may be used as a guide detailed installation information refer to 574 709AC A4098 Sensors and Bases Application Manual For mounting base installation instructions defer to 574 706AC A4098 Smoke Base Installation Instructions This product has been approved by the California State Fire Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety Code See CSFM Listings 7300 2269 0508 and for allowable values and or conditions concerning material presented in this document Additional listings may be applicable contact your local product supplier for the latest status Rev 9 03 2021 TrueAlarm Analog Photoelectric Sensor Sensor Product Selection TrueAlarm Sensor base for A4098 9757 Plate 1 Sensor and Base A4098 9788 base ordered separately one for each A4098 9757 sensor ordered separately 2 Adapter Plate for mounting to surface mounted boxes and 4 square flush mounted be used when retrofitting to existing bases Model number GSAA4098 9757 complies with the Trade Agreement Act and appears in the GSA schedule and Communications Allocation Channel Capability Connections on A4098 9788 Base 4007ES 4010ES 4100ES IDNet 2 or IDNet 2 2 Velocity Range Listed Temperature Range Temperature Range Temperature Range Range communications auto selected 1 address per base address per sensor to 250 sensors devices per channel terminals for in out wiring and shield continuity connection 18 to 14 AWG 0.82 to 2.08 selectable from 0.2 to 3.7 ft obscuration standard sensitivities are 1.5 2.0 2.5 and sensitivities of 0.2 0.5 and 1 are for special applications in clean areas detailed application information including sensitivity selection refer to Installation 574 709AC ft min 0 610 m min to 100 F 0 to 38 C to 122 F 0 to 50 C to 140 F 18 to 60 C to 95 RH from 32 to 122 F 0 to 50 C non condensing White to A4098 9757 Mounting Information 2 Rev 9 03 2021 Mounting Information illustration shows the mounting of the A4098 9757 QuickConnect2 TrueAlarm sensor to the A4098 9788 base TrueAlarm Analog Photoelectric Sensor 3 Rev 9 03 2021 TrueAlarm Analog Photoelectric Sensor 2021 Johnson Controls All rights reserved All specifications and other information shown were current as of document revision and are subject to change without notice listings may be applicable contact your local Autocall product supplier for the latest status Listings and approvals under Tyco Fire Security GmbH and the names listed in this material are marks and or registered marks Unauthorized use is strictly prohibited NFPA 72 and National Fire Alarm Code are registered of the National Fire Protection Association NFPA Rev 9 03 2021