DSC PC5108 v1 0 IS EN NA
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-pc5108-v1-0-is-en-na-0657239418.pdf |
---|---|
Type | |
Size | 632.50 KB |
Downloads |
Text Preview
Jumpers are used to determine which zones will be assigned to the The above diagram shows the jumper settings required to make first 4 zones 9 to 12 and the second 4 zones 13 to 16 Refer to the chart to set the jumpers accordingly Zones A Zones 1 4 B Zones 5 8 Zones Assigned ON ON ON ON OFF ON OFF ON ON OFF ON OFF OFF OFF OFF OFF Disabled Disabled 9 12 13 16 17 20 21 24 25 28 29 32 Add Hardwired Zones module to the Keybus the jumpers on the module section 902 and wait 1 minute section 903 to verify that the module is supervised the zones in sections 002 004 the zones to the appropriate partition in sections 202 209 Warranty Digital Security Controls Ltd warrants that for a period of twelve months from the date of purchase the shall be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such Digital Security Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment its factory This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling damage due to causes beyond the control of Digital Security Controls Ltd Such as lightning excessive voltage mechanical water damage or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd This warranty contains entire warranty Digital Security Controls Ltd neither assumes nor authorizes any other person purporting to act on its behalf modify or to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct or indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure this product Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis However frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to to perform as expected COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the instructions may cause interference to radio and television reception It has been type tested and found to with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules are designed to provide reasonable protection against such interference in any residential installation However there is guarantee that interference will not occur in a particular installation If this equipment does cause interference to television radio reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Problems This is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 1998 Digital Security Controls Ltd Flint Road Downsview Ontario Canada M3J 2J6 416 665 8460 Fax 416 665 7498 Tech Line 1 800 387 3630 in Canada 29001758 R2 Instructions PC5108 module can be used to add up to 8 additional hardwire zones the PC5010 control panel see PC5010 Installation Manual for complete instructions Module Current Draw 35 mA Auxiliary Current 100 mA PTC protected fuseless design Description This can be used to tamper the cabinet the PC5108 is mounted in a normally closed NC switch across TAM and BLK If the tamper not being used connect a piece of wire across TAM and BLK to remove trouble condition is a built in tamper switch on the expander module in the top left corner of the circuit board If the cabinet to mount the PC5108 Zone Expander has the hardware to depress this tamper switch then DO NOT connect to the TAM terminal A U X Used to provide power for devices Maximum current draw is not A U X A U X A U X A U X exceed 100 mA Connect the positive lead of powered devices to VAUX the negative to BLK or any COM terminal E Y B U S The 4 wire KEYBUS connection is used by the panel to commu E Y B U S E Y B U S E Y B U S E Y B U S with the module Connect the RED BLK YEL and GRN terminals to KEYBUS terminals on the PC5010 main control to Z8 Wire the zones according to the description found in the to Z8 to Z8 to Z8 to Z8 Installation Manual Zone Expander 1 O are used to determine which zones will be assigned to the The above diagram shows the jumper settings required to make first 4 zones 9 to 12 and the second 4 zones 13 to 16 Refer to the chart to set the jumpers accordingly Zones A Zones 1 4 B Zones 5 8 Zones Assigned ON ON ON ON OFF ON OFF ON ON OFF ON OFF OFF OFF OFF OFF Disabled Disabled 9 12 13 16 17 20 21 24 25 28 29 32 Add Hardwired Zones module to the Keybus the jumpers on the module section 902 and wait 1 minute section 903 to verify that the module is supervised the zones in sections 002 004 the zones to the appropriate partition in sections 202 209 Warranty Digital Security Controls Ltd warrants that for a period of twelve months from the date of purchase the shall be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such Digital Security Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment its factory This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling damage due to causes beyond the control of Digital Security Controls Ltd Such as lightning excessive voltage mechanical water damage or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd This warranty contains entire warranty Digital Security Controls Ltd neither assumes nor authorizes any other person purporting to act on its behalf modify or to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct or indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure this product Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis However frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to to perform as expected COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the instructions may cause interference to radio and television reception It has been type tested and found to with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules are designed to provide reasonable protection against such interference in any residential installation However there is g