DSC PC5204 v1 0 - Installation Manual - English - PowerSeries Power Supply Module

File Preview
File Preview
Click below to download for free

Text Preview

O1 to O4 Wire the positive lead of the device to the AUX terminal and the to O4 to O4 to O4 to O4 lead to the required output terminal O1 to O4 O1 is supervised in the same manner as the BELL of the PC5010 If O1 is not used if no continuous load is resistor must be or if a siren is connected a 1000W in order to prevent the indication of a trouble see diagram below The following is an example of how to wire various devices to the outputs Warranty Digital Security Controls Ltd warrants that for a period of twelve months the date of purchase the product shall be free of defects in materials and workmanship normal use and that in fulfilment of any breach of such warranty Digital Security Controls shall at its option repair or replace the defective equipment upon return of the equipment its factory This warranty applies only to defects in parts and workmanship and not to incurred in shipping or handling or damage due to causes beyond the control of Security Controls Ltd such as lightning excessive voltage mechanical shock water or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all warranties whether expressed or implied and of all other obligations or liabilities on the part of Security Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd assumes nor authorizes any other person purporting to act on its behalf to modify or to this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct or indirect or consequential loss of anticipated profits loss of time or any other losses incurred by the buyer in with the purchase installation or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested a regular basis However despite frequent testing and due to but not limited to criminal or electrical disruption it is possible for this product to fail to perform as expected COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the instructions may cause interference to radio and television reception It has been type tested and found to with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules are designed to provide reasonable protection against such interference in any residential installation However there is guarantee that interference will not occur in a particular installation If this equipment does cause interference to television radio reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Problems This is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 1996 Digital Security Controls Ltd Flint Road Downsview Ontario Canada M3J 2J6 1 800 387 3630 in Canada 29001761 R2 Instructions PC5204 can be used to provide up to 1.0A of additional current and can used to add up to four high current programmable outputs to the PC5010 panel see PC5010 Installation Manual for complete installation Module Current Draw 20mA Auxiliary Current 1.0A continuous rating 3.0A short term if backup connected PTC protected fuseless design Outputs each output can sink up to 3.0A Transformer requirements 16.5V 40VA Battery requirements 4Ah minimum Descriptions The PC5204 requires a 16V 40VA transformer Connect the transformer an unswitched AC source and connect the transformer to these terminals U XA U XA U XA U XA U X This terminal is used to provide power for devices Maximum draw is not to exceed 1.0A continuous or 3.0A short term with a up battery connected Connect the positive lead of powered de to AUX and the negative to the proper output terminal O1 to O4 This can be used to tamper the cabinet the PC5204 is mounted in a normally closed NC switch across TAM and BLK If the tamper not being used connect a piece of wire across TAM and BLK to remove trouble condition The 4 wire Keybus connection is used by the panel to communi with the module Connect the RED BLK YEL and GRN terminals to the BLK YEL and GRN Keybus terminals on the PC5010 control panel Supply 1 O High Current Outputs Module

Related Files