Edwards 116DEXST-FJ Installation Instructions

Cheshire CT 06410 203 699 3300 Ph Cust Serv Fax Tech Serv Fax Instructions for 116DEXSTC FJ AdaptaBeacon Alarm Strobe Lights for Use in Hazardous Locations 1 1 4 HUB 3 4 HUB 3 4 HUB 3 4 HUB SERIES HOUSING AND GLOBE WITH GUARD 1 Mounting Options 116DEXSTC FJ AdaptaBeacon is an in rush current lim strobe light When pendant wall or ceiling mounted is UL1971 Listed Signaling Appliance for the Hearing Stanchion mount models are UL 1638 Listed Private Mode Emergency Signaling All models are Listed strobe is intended for indoor use in UL listed fire alarm systems and other applications re electrical supervision of signaling circuit field wir This strobe flashes a 360 degree beam of light ap 65 times per minute with a UL 1971 60 cd and ceiling light output per Figure 7 assembled in accordance with these instructions 116DEXSTC FJ visual strobe signal is UL Listed for use Class I Division 1 Groups C and D Class I Division 2 A B C and D Class II Division 1 Group E F and G II Division 2 Group F and G and Class III Division 1 2 hazardous locations with Operating Temperature per the following chart See Table 1 for Electrical strobe is UL and cUL Listed as a Type 3R and 4X enclo See Figure 1 this unit in accordance with the applicable require in the latest edition of the National Fire Alarm Code 72 National Electrical Code NFPA 70 and Cana Electrical Code reduce the risks of ignition of hazardous atmo and shock do not apply power to the unit installation has been completed and unit is assembled and secured Mount using the following applicable method Pendant Mount Models Figure 2 Install the number 116EX P pendant mounting to the main housing Install explosion hanger box not supplied Secure 3 4 19 NPT threaded conduit not supplied to the Install the unit on the conduit Proceed to 2 Ceiling Mount Models Figure 3 Mount the number 116EX C ceiling wall mounting using appropriate hardware not supplied for the mounting surface Proceed to step Bracket Mount Models Figure 4 Install the number 116EX C ceiling wall mouting using appropriate hardware not supplied the mounting surface Install the catalog 116EX B wall mounting elbow to the wall Run the unit wiring through the elbow to wall box Proceed to step 2 Stanchion Mount Models Figure 5 Install the number 116EX S stanchion mounting to the main housing Run the unit wires the 1 1 4 conduit to the appropriate box Install the unit on the conduit to step 2 Connect field earth ground wire to ground screw or ground via conduit system Wire the unit in accordance with Figure 6 See Table for required supply wire temperature ratings As appropriate install the fixture on the mounting reduce the risk of ignition of hazardous atmo and shock keep assembly tightly closed circuits are energized Apply power to the unit and ensure proper function 3100759 ISSUE 1 2004 3 4 1 4 1 4 3 4 3 4 1 4 9 16 7 16 2 Detail of Pendant Mounting 3 Detail of Ceiling Mounting 3 4 1 4 1 16 13 16 3 4 1 2 1 4 Not for use as a Public Mode Fire Alarm 4 Detail of Wall Bracket Mounting 5 Detail of Stanchion Mounting DC polarity of circuit shown in supervisory state signal inactive Circuit polarity to reverse to activate signal Electrical supervision requires wire run to be broken at each device Device for constant input voltage Do not connect to or pulsating voltage Power Source Signaling Device symbol nut symbol Resistor required with system For non fire alarm use i e without field wire supervision installer can tie the two white leads and tie the two black leads together 6 Wiring Diagram 3100759 ISSUE 1 the unit as follows Figure 8 reduce the risk of ignition of hazardous atmo and shock keep assembly tightly closed circuits are energized reduce the risk of ignition of hazardous atmo and shock disconnect from the supply and and allow five 5 minutes for stored energy to before disassembling the unit Loosen the 3 guard screws and remove the guard Loosen the globe and ring assembly set screw Insert suitable tool into the notches in the globe and ring and loosen the assembly by prying in a direction Remove the ring and assembly Refer to Table 2 for the correct replacement catalog and replace the necessary part To replace simply screw the unit on until it seats firmly its gasket Tighten the unit another 1 8 to 1 4 Tighten the setscrew Reinstall the guard where applicable and secure using three supplied screws After the unit is assembled apply power and make the unit functions properly 1 116DEXSTC FJ AdaptaBeacon Strobe Light Specifications Designation 24V DC 24V FWR RMS Operating A To prevent damage to the signal circuit and to assure continued proper functioning DO NOT the unit outside of the Regulated 24V DC FWR range of 16 33V DC V FWR designation Regulated 24 refers to the voltage range of 16 33 volts Max RMS Operating Current is defined as the current over the entire voltage range 2 116DEXSTC FJ 33V DC NPT NPT 1 4 NPT fpm Tube Less Module Module Module Module Bracket Elbow 3 Ratings Wire Marking I Div 2 A B 215 230 Temperature I Div 1 2 II III Div 1 II III Div 2 C D E F G 85 85 120 135 F G 120 135 3100759 ISSUE 1 REQUIRED AS OF CD 1971 Hearing Impaired 60 cd wall Y PLANE OF CD 45 Candela Light Output for Wall Bracket Mount Plane degree angle at side of globe 80 75 CD REQUIRED CD 35 RATING degrees Candela Light Output for Ceiling Mount Y Planes degree angle at bottom of of globe 1 1 1 CD REQUIRED CD 55 RATING