Gamewell-FCI XP95-DM Analog Adderssable Discovery Multi-Sensor

Addressable Devices Addressable Discovery Multi Sensor Analog Addressable Discovery Multi Sensor XP95 DM detector is designed to with the Gamewell FCI 600 Series and ILI95 E3 Series analog addressable alarm control panels The XP95 DM includes both photoelectric and thermal elements integrated into a single device The XP95 DM operates so that it transmits its address to the fire alarm control panel FACP In addition it the analog value from both the photoelectric chamber and the thermal for analysis The high level algorithms designed to prevent false alarms the signals originating from the combined sensors The detector is programmed for pure heat detection pure smoke detection or a of both detections that are dependent on ambient conditions XP95 detectors have identical external dimensions and can be installed in all base The dual Light Emitting Diodes LEDs located on either side of the housing transmit polling and external alarm status The thermal element of the XP95 is designed for the free movement of air flowing around the exposed thermistor photoelectric detection element uses a patented smoke chamber and an infrared sensing feature to obtain maximum sensitivity and selectivity XP95 DM Multi Sensor has both a photoelectric detection chamber and a sensing element The infrared LED in the photoelectric detection chamber a burst of collimated light once per second or emits the light in response to interrogation by the FACP In clean air the photo diode receives no light from emitter When the smoke enters the chamber it scatters light from the emitter the photo diode that is proportional to the smoke characteristics and density the smoke content in the chamber increases the signal from the photo diode XP95 DM monitors the temperature using a single thermistor which provides a output that is proportional to the external air temperature The thermistor is to the normal analog value at a temperature of 25 77 on how you configured the detector programming the on board electronics process the values from each sensing element The Discovery multi sensor detector is automatically programmed for pure heat detection pure smoke detection or a combination of BENEFITS Compatible with the Offers the following Gamewell FCI addressable fire control panels 600 Series ILI95 E3 Series low profile E Z fit 4 inch 10.16 cm 6 inch 15.24 cm Includes an audible sounder base Stores the address in sensor base Comprises thermal Has an optional remote Sets the address by the addressing card Contains a two color Provides fixed point or functions Offers a timed increase causes an alarm LED you assign an XP95 DM detector to a verification zone the occurs local operation when the smoke is detected by the optical element in the sensor head general alarm operation when heat is present the detector senses smoke the local sounder relay or LED in the detector base or group of bases will be activated and pre alarm signal will transmit back to the panel The Aux 4th relay the common control card will transfer If heat is also present the will go into a full General Alarm condition If there is only smoke the smoke clears the panel will automatically restore and trouble conditions are determined by the electronics in the sensor head which also automatically performs drift Normal sensitivity is 2.4 per foot When the sensor is alarm the LEDs in the sensor housing will light continuously The is connected to a two wire signal line circuit SLC carrying XP95 protocol data and a 17 to 28 VDC supply voltage The is insensitive to loop polarity A remote LED indicator may connected Detector Response Modes 1 lists the heat detector mode and various temperatures to each mode Response Response Response 131 55 176 183 131 55 176 183 25 122 129 134 149 25 122 129 141 158 25 122 129 141 158 For air temperatures in the range of 59 F to 131 F 15 C to 55 C the value for a detector in Mode 1 will correspond approximately to the air 1 Heat Detector Response Modes Chart 2 of 3 CS 2403 B Information Discovery Multi Sensor analog addressable and thermal 58000 750 6 15.24 cm ultra low profile EZ Fit mounting base X Pert programming card 45681 250 4 10.16 cm mounting base with X Pert programming 45681 210 6 15.24 cm relay base four wire with X Pert card 6 15.24 cm mounting base with X Pert card and audible alarm sounder Additional blank X Pert programming cards Remote LED 24 V Technical Specifications Current 500 uA average 750 uA peak LED Current 0.004 A Alarm Output 0.004 A 5 VDC Operating Temperature Operating Temperature See table on page 2 Humidity non condensing 0 to 95 SPECIFICATIONS contractor shall furnish and install where indicated the plans a combination photo heat multi sensor Gamewell FCI model XP95 DM with one of the available addressable mounting base options The sensor head and twist lock mounting base be UL Listed and UL Listed as compatible with the fire alarm control panels The base shall free interchange of sensor heads without requiring additional wiring or programming of the sensor head base The smoke sensor shall contain an integral LED shall illuminate when the unit goes into alarm XP95 DM is designed to comply with the following STANDARDS Standard 864 9th Edition LISTINGS AND APPROVALS listings and approvals apply to the modules in this document In some cases certain or applications may not be listed by certain agencies or listing may be in process Consult factory for the latest listing status Listed 9001 Certification a complete listing of all approvals and please visit is a registered trademark Underwriters Laboratories document is not intended be used for installation We try to keep our information up to and accurate We cannot all specific applications anticipate all requirements specifications are subject to without notice of origin U S A Gamewell FCI Clintonville Road CT 06472 1610 B 04 19 Honeywell International Inc