Kidde 3100485-EN R007 BPS Series Fire Alarm Power Supply Technical Reference Manual

Series Fire Alarm Power Technical Reference 3100485 EN REV 007 ISS 28JAN21 and patents 2021 Carrier All rights reserved BPS Series Fire Alarm Power Supply name and E shield logo are trademarks of trade names used in this document may be trademarks or registered trademarks of manufacturers or vendors of the respective products compliance Union directives A This equipment has been tested and found to comply with the limits for a Class digital device pursuant to part 15 of the FCC Rules These limits are designed to reasonable protection against harmful interference when the equipment is in a commercial environment This equipment generates uses and can radiate frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications Operation of this in a residential area is likely to cause harmful interference in which case the will be required to correct the interference at his own expense Fire Department Certificate of Approval MEA 476 91 E XIII R TTE directive Hereby Carrier declares that this device is in compliance the essential requirements and other relevant provisions of Directive 1999 5 EC WEEE directive Products marked with this symbol cannot be disposed of unsorted municipal waste in the European Union For proper recycling return this to your local supplier upon the purchase of equivalent new equipment or dispose it at designated collection points For more information see www recyclethis info battery directive This product contains a battery that cannot be disposed as unsorted municipal waste in the European Union See the product documentation specific battery information The battery is marked with this symbol which may include to indicate cadmium Cd lead Pb or mercury Hg For proper recycling the battery to your supplier or to a designated collection point For more see www recyclethis info contact information see www edwardsfiresafety com information information iii information iii of liability iii messages iii compliance iv 1 covered 1 1 procedure checklist 2 started 3 3 descriptions 3 4 indicators 5 the enclosure 7 Signature modules in the enclosure 8 standard Signature modules 8 SIGA SEC2 modules 8 the circuit board in the enclosure 10 the jumpers 12 wiring class jumpers JP1 and JP2 12 fault detection jumper JP3 12 charging circuit jumper JP4 13 864 programming requirements 15 the DIP switches 16 circuit type SW1 5 to 8 and SW2 1 to 4 16 modes SW1 1 to SW1 3 17 delay SW1 4 19 signal synchronization for Continuous NACs SW2 5 19 relay operation SW2 6 20 power standby operation SW2 7 20 wiring class SW2 8 21 routing 22 the field wiring 23 power wiring 23 wiring 24 Class B wiring 25 Class A wiring 25 200 mA AUX power wiring 27 3100485 EN REV 007 ISS 28JAN21 power circuit wiring 27 relay wiring 28 circuit wiring 29 for opens shorts and ground faults 30 wiring using CC1 S modules 31 the 3 TAMP tamper switch 34 calculation worksheet 35 appliance circuit calculations 37 37 you need 37 method 39 method 40 Genesis signal synchronization 42 of power supplies 42 of visible outputs 43 of visible and audible outputs 43 45 45 circuit notification 46 visible and audible circuit notification 47 visible and audible circuit to Genesis notification 48 audible or visible circuit to Genesis notification 49 visible circuit and conventional audible circuit to Genesis notification 50 split mode circuit with fault tolerance notification 51 split mode circuit with fault tolerance notification 52 Coder to Genesis notification 53 Coder to conventional notification 54 Coder to Genesis visibles and conventional audibles 55 56 control power supply 56 3100485 EN REV 007 ISS 28JAN21 information information product has been designed to meet the requirements of NFPA 72 National Fire Alarm and Signaling Code 864 Standard for Control Units and Accessories for Fire Alarm Systems and CAN ULC S527 11 Standard for Units for Fire Alarm Systems All references to Access Control applications and associated modules in this document are for repair and units only As of December 2 2018 the products covered in this Manual are not listed to the UL 294 for use in access control applications of liability the maximum extent permitted by applicable law in no event will Carrier be liable for any lost profits or opportunities loss of use business interruption loss of data or any other indirect special incidental or damages under any theory of liability whether based in contract tort negligence product liability otherwise Because some jurisdictions do not allow the exclusion or limitation of liability for consequential or damages the preceding limitation may not apply to you In any event the total liability of Carrier shall not the purchase price of the product The foregoing limitation will apply to the maximum extent permitted by law regardless of whether Carrier has been advised of the possibility of such damages and regardless whether any remedy fails of its essential purpose in accordance with this manual applicable codes and the instructions of the authority having is mandatory every precaution has been taken during the preparation of this manual to ensure the accuracy of its Carrier assumes no responsibility for errors or omissions messages messages alert you to conditions or practices that can cause unwanted results The advisory messages in this document are shown and described below Warning messages advise you of hazards that could result in injury or loss of life They tell you which to take or to avoid in order to prevent the injury or loss of life Caution messages advise you of possible equipment damage They tell you which actions to take or to in order to prevent the damage Note messages advise you of the possible loss of time or effort They describe how to avoid the loss Notes also used to point out important information that you should read 3100485 EN REV 007 ISS 28JAN21 compliance equipment can generate and radiate radio frequency energy If the equipment is not installed in accordance this manual it may cause interference to radio communications This equipment has been tested and found comply with the limits for Class A computing devices pursuant to Subpart B of Part 15 of the FCC Rules These are designed to provide reasonable protection against such interference when this equipment is operated in commercial environment Operation of this equipment is likely to cause interference in which case the user at own expense will be required to take whatever measures may be required to correct the interference 3100485 EN REV 007 ISS 28JAN21 installation manual is intended for use by installers and field technicians It provides the installation wiring diagrams DIP switch settings etc required to install and set up BPS Series fire alarm power covered following table lists the BPS Series fire alarm power supply models that are covered in this manual number supply 120 V 50 60 Hz 6.5 A max output supply 120 V 50 60 Hz 6.5 A max output rack mount Canada supply 240 V 50 60 Hz 6.5 A max output supply 120 V