Kidde 3102550-EN R002 Genesis EG1 Series Signaling Appliance Installation Sheet

EG1 Series Signaling Installation Sheet EG1 Series signaling appliances feature Field configurable horn and strobe outputs See Figure 2 Enhanced synchronization circuitry to comply with the latest of UL 1638 and CAN ULC S526 wiring test points on the front of the appliance when the is removed Synchronized operation requires a separately installed device See the control unit or remote booster auxiliary supply compatibility list for compatible synchronization devices Equipment damage hazard Using excessive force when the appliance cover may damage the cover and prevent it latching in place configure the signaling appliance Remove the appliance cover See Figure 1 a small flat bladed screwdriver into the slot at the bottom of appliance pull up on the screwdriver to pry the bottom of the cover down and away from the appliance the bottom of the cover out and over the top of the appliance Set the light and sound output switches See Figure 2 EG1 Series horns strobes and horn strobes are compact fire alarm signaling appliances designed for indoor dry See Table 1 through Table 3 for a list of models Replace the appliance cover 1 Removing and replacing the cover 1 Horn models 2 Strobe models wall horn red FIRE wall horn red no marking wall horn white FIRE wall horn white no marking wall strobe red FIRE wall strobe red no marking wall strobe white FIRE wall strobe white no marking 3 Horn strobe models wall horn strobe red FIRE wall horn strobe red no marking wall horn strobe white FIRE wall horn strobe white no marking 2018 United Technologies Corporation 4 3102550 EN REV 002 ISS 03APR18 2 Light and sound output settings 2 3 4 4 Mounting on a 1 gang electrical box Constant low dB Constant high dB T3 temporal low dB T3 temporal high dB 75 candela 30 candela 15 candela Electrical box EG1 Series signaling appliance Captive screw 2X Appliance cover Using a trim ring is optional except when installing the signaling on electrical boxes greater than three inches wide For instructions when using a trim ring see Genesis EG1 Trim Ring Installation Sheet P N 3102552 EN and wire this device in accordance with applicable national and codes ordinances and regulations Electrical supervision requires that you break the wire run at terminal Do not loop the signaling circuit field wires around the Do not use Genesis EG1 Series strobe and horn strobe appliances in applications where signal power is cycled on off such as coded or private mode signaling systems install the appliance Remove the appliance cover and testing Equipment damage hazard To maintain the required agency do not change factory applied finishes unit is not serviceable or repairable Should the unit fail to contact the supplier for replacement a visual and operational inspection in accordance with codes and standards or as directed by the local authority jurisdiction wiring test points are available on the front of the appliance when cover is removed The test points let you easily spot check the field wiring without the need to remove the appliance from the wall Figure 5 Connect the field wiring Observe signal polarity for the appliance operate properly See Figure 3 5 Test points Attach the appliance and if used the trim ring backplate to the box Do not overtighten the screws See Figure 4 Replace the cover by hooking it to the top of the appliance and snapping the bottom into place See Figure 1 Test the unit for proper operation 3 Wiring Horn strobe circuit in signal polarity shown in the active condition Horn strobe circuit out Marking indicates signal polarity when the circuit is active 4 3102550 EN REV 002 ISS 03APR18 voltage current signal type output pattern output flash rate distribution size torque Mounting screws screws W to 33 VDC 16 to 33 VFWR Table 4 to Table 6 or T3 temporal Table 7 Table 8 30 or 75 candela fps flash per second approx Figure 6 max between any two devices determine allowed wire resistance refer to specifications and the specifications the synchronized signal source to 18 AWG 0.75 to 2.50 mm lbf in 1.8 N m max lbf in 1.4 N m max 4 5 8 1 1 8 in 7.62 11.75 2.86 cm Figure 7 inches 1.8 cm center electrical 1 rings covers environment humidity temperature Electrical boxes must be at least 1 1 2 in 3.81 cm deep Electrical greater than three inches wide require a trim ring 2 gang 4 inch octagon square EG1TW Table 9 to Table 11 to 122 0 to 50 to 93 noncondensing to 158 40 to 70 4 Operating current horn models setting T LOW T HIGH to 33 VDC mA mA 5 Operating current strobe models setting 30 75 to 33 VDC mA to 33 VFWR mA mA to 33 VFWR mA 6 Operating current at 16 to 33 VDC horn strobe models setting 30 75 C LOW T LOW T HIGH to 33 VFWR mA mA to 33 VDC mA mA 7 Sound output horn and horn strobe models setting 464 dBA dBA dBA dBA T LOW T HIGH 8 Sound pattern ULC and 115 and 130 and 135 and 140 in output dBA dBA dBA dBA 9 Horn replacement covers compact wall horn red no marking compact wall horn white ALERT compact wall horn white no marking 10 Strobe replacement covers compact wall strobe red no marking compact wall strobe white ALERT compact wall strobe white no marking 11 Horn strobe replacement covers compact wall horn strobe red no marking compact wall horn strobe white ALERT compact wall horn strobe white no 6 Light distribution 20 15 10 5 10 15 20 25 Measured Horizontal left Horizontal right Vertical bottom Figure 6 shows the light distribution for 75 cd output For 30 cd multiply point by 0.40 For 15 cd output multiply point by 0.20 UL minimum 3102550 EN REV 002 ISS 03APR18 4 7 Dimensions information rating compliance Canada 24 DC and 24 FWR device complies with part 15 of the FCC Operation is subject to the following two 1 This device may not cause harmful and 2 this device must accept any received including interference that cause undesired operation Class A digital apparatus complies