Kidde 3102551-EN R002 Genesis EGC Series Signaling Appliance Installation Sheet

EGC Series Signaling Installation Sheet Equipment damage hazard Using excessive force when the appliance cover may damage the cover and prevent it latching in place configure the signaling appliance Remove the appliance cover See Figure 1 a small flat bladed screwdriver into the slot at the bottom of appliance pull up on the screwdriver to pry the bottom of the cover down and away from the appliance the bottom of the cover out and over the top of the appliance Set the light and sound output switches See Figure 2 Replace the appliance cover 1 Removing and replacing the cover EGC Series horns strobes and horn strobes are ceiling or plug in fire alarm signaling appliances designed for dry applications See Table 1 for a list of models horn red FIRE horn white FIRE strobe red FIRE strobe red no marking strobe white FIRE strobe white no marking horn strobe red FIRE horn strobe red no marking horn strobe white FIRE horn strobe white no marking 1 Models EGC Series signaling appliances feature Field configurable horn and strobe outputs See Figure 2 Enhanced synchronization circuitry to comply with the latest of UL 1638 and CAN ULC S526 wiring test points on the front of the appliance when the is removed Synchronized operation requires a separately installed device See the control unit or remote booster auxiliary supply compatibility list for compatible synchronization devices 2019 United Technologies Corporation 4 3102551 EN REV 002 ISS 24JUN19 2 Light and sound output settings 3 Mounting diagram 115 candela 75 candela 30 candela 15 candela Constant low dB Constant high dB T3 temporal low dB T3 temporal high dB Temporal 3 coding is the required output for fire notification per NFPA 72 Any device coding other than Temporal 3 is at discretion and approval of the local authority having jurisdiction and wire this device in accordance with applicable national and codes ordinances and regulations Electrical supervision requires that you break the wire run at terminal Do not loop the signaling circuit field wires around the install the appliance Attach the wiring plate and if used the trim plate to the electrical See Figure 3 The trim plate is ordered separately Connect the field wiring Observe signal polarity for the appliance operate properly See Figure 4 Remove the shorting clip Figure 4 item 3 Retain for future use Plug the appliance into the wiring plate by setting the appliance on top of the wiring plate and then snapping the bottom into See Figure 5 unplug the appliance press the spring clip on the bottom and lift the appliance away from the wiring plate Test the unit for proper operation Electrical box Trim plate optional Wiring plate Machine screw 2X supplied with wiring plate EGC Series signaling appliance 4 Wiring Horn strobe circuit in signal polarity shown in the active condition Horn strobe circuit out Shorting clip 4 3102551 EN REV 002 ISS 24JUN19 5 Removing and replacing the appliance and testing Equipment damage hazard To maintain the required agency do not change factory applied finishes unit is not serviceable or repairable If the unit fails to operate the supplier for a replacement a visual and operational inspection in accordance with codes and standards or as directed by the local authority jurisdiction wiring test points are available on the front of the appliance when cover is removed The test points let you easily spot check the field wiring without the need to remove the appliance from the wall Figure 6 6 Test points Marking indicates signal polarity when the circuit is active voltage current signal type output pattern output flash rate to 33 VDC 16 to 33 VFWR Table 2 to Table 4 or T3 temporal Table 5 and Table 6 Table 7 and Table 8 30 75 or 115 cd fps flash per second approx distribution D center electrical rings covers environment humidity temperature Figure 7 max between any two devices determine allowed wire resistance refer to specifications and the specifications thesynchronized signal source 1.82 in 17.27 4.62 cm Figure 8 in 0 cm 2 gang 4 inch octagon square EGCTW Table 9 to 122 0 to 50 to 93 noncondensing to 158 40 to 70 2 Operating current horn models setting T LOW T HIGH to 33 VDC mA mA 3 Operating current strobe models setting 30 75 115 to 33 VDC mA setting T LOW 4 Operating current horn strobe models 30 75 to 33 VDC mA T HIGH mA to 33 VFWR mA mA to 33 VFWR mA to 33 VFWR mA mA 5 Sound output horn models setting 464 dBA dBA T LOW T HIGH dBA dBA 6 Sound output horn strobe models setting 464 dBA dBA dBA dBA T LOW T HIGH 7 Sound pattern horn models ULC and 55 and 50 dBA 3102551 EN REV 002 ISS 24JUN19 4 8 Dimensions information rating compliance 24 DC and 24 FWR device complies with part 15 of the FCC Operation is subject to the following two 1 This device may not cause harmful and 2 this device must accept any received including interference that cause undesired operation Class A digital apparatus complies with ICES 003 dry Canada information contact information see www kiddelifesafety com 8 Sound pattern horn strobe models ULC and 35 and 25 and 35 and 25 dBA 9 Horn replacement covers ceiling horn red FIRE ceiling strobe white ALERT ceiling horn white FIRE ceiling strobe white no marking ceiling strobe red FIRE ceiling strobe white ALERT ceiling strobe white FIRE ceiling strobe white no marking ceiling horn strobe red FIRE ceiling horn strobe white ALERT ceiling horn strobe white FIRE ceiling horn strobe white no marking 7 Light distribution 15 10 15 20 Horizontal left Horizontal right Vertical below Vertical above Measured UL minimum for cd appliance