Notifier N-ANN-S PG Serial Parallel Printer Interface Module

N ANN S PG Printer Module N ANN S PG Interface module connects either a serial or printer with a compatible Fire Alarm Control Panel to print real time logs of system events detector status and event histories N ANN S PG and the FACP communicate over a two wire interface employing the ANN BUS communication for An additional two wires are used for 24 volt DC power A four conductor unshielded cable may be used for both and data communications to eight N ANN S PGs may be connected to the ANN Bus each FACP Auto configure menu selection allows programmer to bring the devices attached to the ANN BUS on line quickly Surface mounts directly to wall Can be remotely located up to 6,000 feet 1,829 m from the May be powered by 24 VDC from the host FACP or by power supply requires 24 VDC Connects a remote printer using a standard cable DB 9 for serial printer DB 25 for a parallel printer Operating Voltage 24 VDC Current Alarm and Standby 45mA Ambient Temperature 32 to 120 0 to 49 Relative Humidity 93 2 RH noncondensing at 32 2 90 3 Maximum wiring distance from FACP 6,000 ft 1,829 m Dimensions 6.00 15.2 cm high x 7.76 19.7 cm wide x 3.7 cm deep For use indoors in a dry location Connections to FACP are power limited and supervised Listings and Approvals listings and approvals below apply to the N ANN S PG In cases certain modules may not be listed by certain agencies or listing may be in process Consult fac for latest listing status UL S635 CSFM 7120 0028 242 MEA 442 06 E Vol 2 D 10 ANN BUS THE DEVICES ON THE ANN BUS FROM POWER SUPPLY devices can be powered by an auxiliary power sup when available panel power is exceeded See FACP man for information DEVICE ADDRESSING ANN BUS device requires a unique address ID Num in order to communicate with the FACP A maximum of devices can be connected to the FACP ANN BUS com circuit See the FACP manual for more information REQUIREMENTS N ANN S PG connects to the FACP ANN BUS communi circuit To determine the type of wire and the maximum distance calculate the total worst case current draw for modules on a single 4 conductor bus Use the following to determine the maximum distance the modules can be from the FACP In general the wire length is limited by but for heavier wire gauges capacitance is the lim factor These cases are marked in the chart with an aster Maximum length can never be more than 6,000 feet m regardless of gauge used 10 25 07 Page 1 of 2 Pair Wiring Distance FACP to last ANN BUS Module Worst Case Draw amps Gauge Gauge Gauge Gauge max ft 565 m ft 282 m ft 188 m ft 141 m ft 113 m ft 94 m ft 81 m ft 70 m ft 63 m ft 56 m ft 1,429 m ft 715 m ft 476 m ft 357m ft 286 m ft 238 m ft 204 m ft 179 m ft 159 m ft 143 m 6,000 ft 1,829 m ft 1,137 m ft 758 m ft 569 m ft 455 m ft 379 m ft 325 m ft 284 m ft 253 m ft 227 m 6,000 ft 1,829 m ft 1,800 m ft 1,200 m ft 900 m ft 720 m ft 600 m ft 514 m ft 450 m ft 400 m ft 360 m and power wiring are and power limited Connectors connection to Sample shows NFW 50 refer to your panel FACP Manual actual connections Connection to FACP is a registered trademark of Honeywell International Inc by Honeywell International Inc All rights reserved Unauthorized use this document is strictly prohibited document is not intended to be used for installation purposes We try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice more information contact Notifier Phone 203 484 7161 FAX 203 484 7118 in the U S A 2 of 2 DN 7103 A 10 25 07