Notifier NBG-12WL & NBG-12WLSP SWIFT Wireless Pullstations

NBG 12WL NBG 12WLSP SWIFT Wireless Pullstations NOTIFIER SWIFT addressable pull station is a dual action pull station with a key lock reset feature that provides one alarm initiating input The pull station features similar design and durable construction characteristics as the counterpart to blend seamlessly throughout the environment device communicates to the FACP through the SWIFT mesh and gateway and is powered by 4 batteries offering a 2 UL listed battery life is fast and straightforward by using a mounting plate that be surface mounted Once the mounting plate is firmly attached the wall the pull station is snapped into place and locked down 3 screws mechanical operation is simple and easy to use in an emer with a PUSH IN PULL DOWN handle that latches in the down to clearly indicate the station has been operated while the appears on top of the handle in bright yellow indicating the operation of the station wireless pull station meets the Americans with Disabilities Act Guidelines ADAAG controls and operating mecha guidelines section 4.1.3 13 and the Americans with Disabili Act ADA requirement for a 5 pound maximum pull force to the pull station and conforms to ANSI UL Standard 38 SWIFT wireless system offers intelligent addressable devices provide secure reliable communication to the Fire Alarm Con Panel FACP across a Class A mesh network Wireless devices an opportunity for applications where it is costly concrete buried wires obtrusive surface mount conduit or dangerous asbestos to use traditional wired devices In both wired and wireless devices can be present on the FACP providing an integrated wired wireless solution for installation potential mesh network within the SWIFT system creates a child parent between the devices so that each device has two par providing a second path for communications on every device If device can no longer operate for any reason the rest of the can still communicate with each other directly or through or more intermediate devices Once an initial mesh network is mesh restructuring automatically occurs to find the stron paths possible within the network SWIFT system also engages frequency hopping to prevent sys interference whether intentional or accidental Each device with part 15 of the FCC rules meaning operation is subject the following two conditions 1 The device may not cause harmful and 2 The device must accept any interference including interference that may cause undesired operation Easy fast wireless installation Participates in a Class A mesh network Built in tri color LED which is visible through the handle of the flashes in normal operation and latches steady red when alarm Handle latches in down position and the word to clearly indicate the station has been operated Maintenance personnel can open station for inspection and setting without causing an alarm condition Standard wheel for setting the SLC address For use in commercial applications Smooth dual action design Meets ADAAG controls and operating mechanisms guidelines 4.1.3 13 meets ADA requirement for 5lb maximum force Braille text on station handle Meets UL 38 Standard for Manually Actuated Signaling Boxes Highly visible Made of durable polycarbonate material Attractive shape and textured finish Key reset Control Panels NFS2 3030 NFS2 640 NFS 320 NFS 320SYS NFW 100X NFW 50X and Ordering Information NBG 12WL Wireless addressable pullstation Requires 4 CR batteries included NBG 12WLSP Wireless addressable pullstation Spanish text 4 CR 123A batteries included FWSG FlashScan Wireless SWIFT Gateway 1 SWIFT Gate is required for each wireless mesh and supports up to 49 detectors or modules Connects to the SLC loop of a panel using FlashScan protocol Power may be sup by the SLC circuit or via an optional 24VDC input Use of the 24VDC input may be more convenient for service as it for powering down a gateway without shutting down an SLC loop FWD 200P FlashScan wireless photo detector one B210W base for installation Requires 4 CR 123A included FWD 200ACCLIMATE FlashScan wireless Accli heat and photo detector using combined heat and smoke information and the ability to automatically adjust sensitiv based on ambient changes in the environment Requires one 10 30 2018 Page 1 of 2 Transmit RF Power 17 dBm Frequency Range 902 928 MHz Range 32 to 120 0 to 49 10 to 93 Non condensing Type 4 Panasonic CR123A or 4 Duracell DL123A Life 2 year minimum Replacement Upon TROUBLE BATTERY LOW display and during annual maintenance 5.6 142 mm H x 4.2 107 mm W x 2.1 53 mm D Listings and Approvals listings and approvals below apply to the NBG 12WL In some certain modules may not be listed by certain approval agen or listing may be in process Consult factory for latest listing sta Listed S692 7150 0028 0504 ID AUBWFSPS ID 573X WFSPS Fire Dept COA 6217 6218 6268 Approved base for installation Requires 4 CR 123A batteries FWH 200ROR135 FlashScan intelligent wireless rate of rise heat detector Requires one B210W base for installation 4 CR 123A batteries included FWH 200FIX135 FlashScan intelligent wireless fixed tempera 135 heat detector Requires one B210W base for installa Requires 4 CR 123A batteries included FW MM FlashScan wireless monitor module Used to monitor with mechanical contact actuation Includes a special with a built in tamper magnet Recommended for installa in a SMB500 WH box ordered separately rather than a backbox for best performance Requires 4 CR 123A bat included FW RM Wireless relay module for use with the FWSG wireless Includes a special cover with a built in tamper magnet for installation in an SMB500 WH box ordered rather than a metal backbox for best performance 4 CR 123A batteries included WAV CRL WAV CWL SWIFT Wireless Addressable A V bases 8 CR 123A batteries included Requires a non com ceiling System Sensor L series notification device ordered W SYNC Wireless sync module Requires 4 CR 123A batteries SMB500 WH Optional surface mount backbox B210W Detector base used for wireless detectors Includes a magnet so that wireless devices can establish installed tampered states SWIFT Tools Programming and diagnostic utility Free download www notifier com For installation on a typically laptop PC an approved version of Windows See Minimum System for SWIFT Tools Requires the W USB radio dongle for communication with SWIFT Wireless devices W USB Wireless USB radio antenna dongle that plugs into the port of a PC running SWIFT Tools The W USB provides a link with SWIFT Wireless devices that are within 20 feet and have not formed a mesh Alternately the devices have formed a mesh bringing the PC W USB range 20 ft of the gateway for that mesh will allow SWIFT to acquire information on all devices in that mesh including signal strength for all links Clintonville Road CT 06472 document is not intended to be used for installation purposes try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice Plus FlashScan NOTIFIER System Sensor and are registered trademarks of Honeywell International Inc Micro and Windows are registered trademarks of Microsoft Corporation is a registered trademark of Duracell U S Operations Inc is a registered trademark of Panasonic Corporation by Honeywell Internation