Notifier NION-2C8M-Product-Installation-Document

2C8M NION Installation Document document covers the procedures and specifications for installing the above listed unit and when information regarding configuration on the monitored device For more detailed configura and operation information refer to the Network Installation manual Echelon Local Area Server or BCI 3 manual as appropriate of the 2C8M NION 2C8M NION 2 Control 8 Monitor is a discrete input output interface used on the network The NION a gateway to the network for equipment and control panels that have dry contacts It allows conventional and equipment to operate on the same network as equipment with an EIA 232 output 2C8M NION connects a LonWorks FT 10 or fiber network and discrete monitored devices and conven control panels It provides a single two way communication channel for discrete inputs and outputs when to a control panel NIONs are specific to the type of network to which they connect FT 10 or fiber transceiver type must be specified and ordered separately when ordering the NION 2C8M NION can be powered by any 24VDC power limited source with battery backup which is UL listed for with fire protective signaling units Power must be supervised or placed within 20 ft of the NION with connec run in conduit 2C8M NION mounts in an enclosure NISCAB 1 or CHS 4L in CAB 3 4 series enclosure with conduit Do not use the CHS 4 chassis For chassis mounting the NION requires the Use of the CHS 4 can cause a circuit short on the NION motherboard with results and and and and and Input Input Input Input Input 2 2 2 2 2 1 1 1 1 1 i nP i nP i nP i nP i n EOL resistor EOL resistor EOL resistor EOL resistor EOL resistor parallel with parallel with parallel with parallel with parallel with 1 8 1 8 1 8 1 8 1 8 Configura Configura Configura Configura Configura Jumpers Jumpers Jumpers Jumpers Jumpers 1 2C8M NION Board Layout 50815 2C8M NION Installation Rev B 05 05 03 50815 Rev B ECN 02 298 ECN 02 298 ECN 02 298 ECN 02 298 ECN 02 298 Description NION can be installed in the following environmental conditions range of 0 to 49 32 120 humidity non condensing at 30 86 Use only wire for power limited systems limited wire runs use type FPLR FPLP FPL equivalent cabling per NEC 760 NION is designed to be installed on a wall within 20 feet of the monitored equipment in the same room The of hardware used is at the discretion of the installer but must be in accordance with local code requirements When using the DFXC transceiver with the 2C8M NION be sure to use the longer and header adapter provided with the DFXC transceiver Power Requirements 2C8M NION requires 24 VDC 0.10 A nominal and battery backup in accordance with local code It can be powered by any power limited 24 VDC source which is UL or ULC listed as appropriate for area for use with fire protective signaling units Always remove power from the NION before making any changes to switch settings removing or installing option modules SMX network modules and software upgrade or damage may result LEDs LEDs on the front panel of the 2C8M NION provide information about module operation The table below the possible conditions Refer to Figure 1 2C8M NION Board Layout for the position of each of the LEDs listed below LED provides information on network communication and node by one of the modes listed below slow NION is functioning normally fast NION is bound but not communicating or the was lost LED provides information on node binding and NGM status by of the three modes listed below NION is bound NION is not bound Status LED is off NION is in a fault condition or the PROM chip was not an output has been energized an input is active NION LED Status Information 50815 2C8M NION Installation Rev B 05 05 03 Configuration and Connections NION accepts eight normally open or normally closed dry contact inputs Each normally open input is by an end of line resistor These inputs are wired to a 16 point plug in terminal strip in the following 1 1 input line 2 common 8 15 input line 16 common PCB is labeled and the terminals are numbered for convenience Inputs are rated for 18V nominal 1.8mA current and 2,000 ohm maximum resistance normally open input circuit requires a 10k EOL resistor installed in parallel with the contact Normally closed inputs are not supervised and cannot be used for fire applications each input style NO or NC by setting jumpers JP4 through JP11to the desired settings using the following input also has a related pair of LEDs a red LED to indicate an alarm state short and a yellow LED to indicate trouble state open Open Open Open Open Open This diagram is also printed on the circuit next to the LEDs 2C8M NION provides two SPDT relay outputs The relays are rated at 5A 30VDC They can be wired for open or normally closed operation All rated loads are resistive Inductive and tungsten loads will be For special applications consult with a NOTIFIER applications engineer Input and output lines should not 2000ft Closed Closed Closed Closed Closed Open Open Open Open Open Closed Closed Closed Closed Closed Open Open Open Open Open Output Connector Configuration order to utilize all features available with the 2C8M NION the 2C8M Scheduling Plug In utility must be at the system workstations General Plug In setup information can be found in the Workstation manual 50815 2C8M NION Installation Rev B 05 05 03 50815 2C8M NION Installation Rev B 05 05 03