Notifier SEP-SW(A), SEP-SPSW(A) Dual Strobe Expander Plates for Emergency Communications

SEP SW A SEP SPSW A Strobe Expander Plates for Communications new SpectrAlert Advance Dual Strobe and Dual Strobe Speaker Expander Plates lower costs and improve aes by performing the functions of 2 3 devices for emer communications applications costs speed installation and improve aesthetics on emer communications applications that require fire and emer warnings by combining the functions of two to three on a single mounting plate and back box SpectrAlert Dual Strobe and Dual Strobe with Speaker Expander provide dual strobe and speaker strobe functionality easy for a single person to wire and install Simply mount plate to a junction box and connect the field wiring to the To complete the installation hinge and attach the or speaker strobe device with a single captured mount screw Strobe and Dual Strobe with Speaker Expander Plates designed to be used in 12 or 24 volt DC or FWR full wave systems Amber lens strobes are UL 1638 Listed Signaling Appliances for Private Mode General Utility A table is also provided to show the candela rating the UL 1971 test procedures All SpectrAlert Advance are suitable for use in synchronized systems The Sensor MDL module may be used to provide synchro See installation document I56 3829 001R for mounting details and restrictions UL 1638 Listed amber lens strobe included Meets DOD specification requirements Field selectable candela settings 15 15 75 30 75 95 110 115 please refer to Candela Rating for UL 1971 Table Automatic selection of 12 or 24 volt operation at 15 and 15 candela Compatible with System Sensor synchronization protocol Optional tamper resistant screw included Designed to be used in 12 or 24 volt DC or FWR systems Rated from 32 to 120 0 to 49 SEP SPSW is compatible with and accomodates the instal of SPSW SPSWH SPSW P SPSWV SPSWV P and SEP SW is compatible with and accomodates the installa of SW SWH SW P and SWH P Used in flush mounted and surface mounted applications Devices and SEP SPSW Strobe Device Sold Separately Temperature 32 to 120 0 to 49 Humidity 10 93 non condensing Flash Rate 1 flash per second Voltage strobes Regulated 12VDC FWR or regu 24DC FWR Voltage Range includes fire alarm panels with in sync 8 to 17.5V 12V nominal or 16 to 33V 24V Voltage with MDL Sync Module 9 to 17.5V 12V or 17 to 33V 24V nominal terminal wire gauge 12 to 18 AWG Plate Only SEP SW 4 in x 4 in x 1.5 in single gang double gang 4 in SEP SPSW 4 in x 4 in x 2.125 in or deeper Plate with Strobe or Speaker Strobe Device SEP SW SEP SPSW L 9.6 in 245 mm W 5.1 in 130 D 3.7 in 94 mm SPSEP BBSW SEP BBSW L 10.1 in 257 mm W 5.6 in mm D 2.5 in 64 mm Box Skirts SPSEP BBSW SEP BBSW 4 in x 4 in x 2.125 in Weight SEP SW SEP SPSW 0.88 lb 0.4 kg SPSEP BBSW SEP BBSW 0.69 lb 0.31 kg 02 10 2012 Page 1 of 2 Current Draw Data Max Strobe Current Draw mA for SEP SW SEP SPSW Amber Strobe Only to 17.5 V to 33 V Derating for Amber Lens Strobe Switch Rating 1638 Cd Rating for profile UL 1971 UL 1971 is not applicable to emergency communication devices these readings were obtained using the measurement procedure under UL 1971 Listings and Approvals listings and approvals apply to the modules specified in document In some cases certain modules or applications not be listed by certain approval agencies or listing may in process Consult factory for latest listing status UL Listed S3593 ULC Listed S5512 CSFM 7300 1653 0221 FM Approved Line Information suffix indicates ULC Listed model Strobe Expander Plate for use with SW SWH P SWH P includes amber lens strobe Back Box Skirt for use with SW SWH SW P and Speaker Strobe Expander Plate for use with SPSWH SPSW P SPSWV SPSWV P and SPSWH includes amber lens strobe Back Box Skirt for use with SPSW SPSWH SPSWV SPSWV P and SPSWH P and FlashScan are registered trademarks of Honeywell Inc by Honeywell International Inc All rights reserved Unauthorized use this document is strictly prohibited document is not intended to be used for installation purposes We try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice more information contact Notifier Phone 203 484 7161 FAX 203 484 7118 in the U S A 2 of 2 DN 60711 A 02 10 2012