Notifier SWIFT® FWSG FlashScan® Wireless Gateway

SWIFT FlashScan Wireless Gateway SWIFT Wireless System can be applied in many situa that are problematic for traditional wired devices In where areas of a building are difficult or impossible to visually sensitive or have restricted access SWIFT wire sensors provide an efficient reliable solution wireless devices communicate via a proprietary wire mesh protocol to communicate with a NOTIFER ONYX alarm system by means of a SWIFT Wireless Gateway SWIFT Gateway connects to the SLC loop of an NFS2 NFS2 640 or NFS 320 panel running version 24 firm or higher using FlashScan protocol New type IDs for devices are supported that allow the FACP to display events such as alarms and trouble indications as well as trouble conditions required for wireless devices This eliminates the need for a supplementary annunciator wireless event messages devices in a SWIFT network develop parent child links with other devices in the mesh so that a originating from a remote device hops to the clos parent device and then to successive parent devices until message reaches gateway Alternate paths are also identi and supervised by the SWIFT protocol providing approved A wireless communication If a device does not have an communication path with adequate signal an additional device such as a wireless module may installed in between so that it will act as a repeater SWIFT Gateway system supports up to 50 devices 1 Gateway and up to 49 wireless detectors and monitor The Gateway assumes one SLC address module each wireless device assumes one module or detector The maximum number of gateways on a system is by the number of available SLC addresses on the or a maximum of 4 gateways within common wireless SWIFT system has been designed so that it can be using only typical hand tools and magnets However SWIFT Tools PC utility provides many benefits that can the process of performing a site evaluation Site Sur installing a system Mesh Configuration or extracting information from the system Diagnostics The utility on a Windows laptop and uses a USB radio antenna inserted into a USB slot to communicate with wire devices within range of the PC Once devices have a mesh SWIFT Tools can provide current information all devices in the mesh as long as the PC is within range of SWIFT Gateway result is a fire system that combines both wired and wire detection and presents all event information at the panel network displays when used SWIFT wireless mesh protocol specifically for fire and life systems Operates in 902 928 MHz frequency Patented cascading wave mesh operation provides a of redundant communication paths that has approved for Class A Wireless Devices FlashScan Wireless Gateway In the event that a communication path is interrupted at point by a change in the radio environment the mesh system will use the redundant or backup path In the event that any links cannot be established with suf signal strength any SWIFT device can be added to as a repeater eliminating the need for wired repeat A wireless monitor module is recommended for this as modules are not subject to spacing require Each SWIFT gateway system support up to 50 devices 1 gateway and up to 49 SWIFT devices Multiple SWIFT wireless mesh networks can be installed on same fire alarm control panel or on multiple panels in same area Up to 4 wireless networks can be installed with overlapping network coverage Site Survey feature allows for an evaluation of a site before installation including a series of point to point commu tests and a background scan for radio interference SWIFT wireless devices use a standard wheel for setting the SLC address SWIFT wireless devices use 4 CR 123A lithium batteries CR123A or Duracell DL123A which are UL for a battery life of 2 years Tools Tools is a Windows PC based utility that is used for evaluation system configuration and diagnostics The Tools program is used with the W USB adapter to com with wireless devices that are not joined in a net or with one or more wireless gateways and all devices have formed a network with each gateway A graphic rep of the wireless network provides important system in an effective format including communication links sig strength battery voltage and more 9 30 2015 Page 1 of 3 operation is supported allowing you to perform site and system configuration and installation can be without using SWIFT Tools when necessary LEDs on SWIFT devices provide feedback for At any point only one instance of SWIFT Tools run on a laptop or PC Tools has the following utilities Site Survey Create Mesh Network Diagnostics Tools works in a wireless environment with the FWSG devices within a range of approximately 20 feet Tools is designed for systems running Microsoft Win SYSTEM REQUIREMENTS System Windows XP Professional SP3 Vista 7 and Windows 8 32 bit and 64 bit Drive 20 GB hard drive space with minimum 1GB free on hard disk Minimum 512MB RAM speed 1GHz minimum 2.4 GHz recommended 512K Cache of SWIFT Tools Diagnostic Utility Components and Ordering Infor FWSG FlashScanWireless SWIFT Gateway 1 SWIFT is required for each wireless mesh and supports to 49 SWIFT detectors or modules Connects to the SLC of a compatible panel using FlashScan protocol may be supplied by the SLC circuit or via an optional input Use of the 24VDC input may be more convenient for ser as it allows for powering down a gateway without shutting an SLC loop FWD 200P FlashScan intelligent wireless photo detector one B210W base for installation Requires 4 batteries included FWD 200ACCLIMATE FlashScan wireless heat and photo detector using combined heat smoke sensor information and the ability to automati adjust sensitivity based on ambient changes in the Requires one B210W base for installation 4 CR 123A batteries included FWH 200ROR135 FlashScan intelligent wireless rate of 135 heat detector Requires one B210W base for Requires 4 CR 123A batteries included FWH 200FIX135 FlashScan intelligent wireless fixed tem 135 heat detector Requires one B210W base installation Requires 4 CR 123A batteries included FW MM FlashScan wireless monitor module Used to devices with mechanical contact actuation a special cover with a tamper magnet built in Rec for installation in a SMB500 box ordered sepa rather than a metal backbox for best performance with 4 Panasonic CR123A or 4 Duracell DL123A bat See data sheet for more information FW RM Wireless relay module for use with the FWSG gateway Includes a special cover with a tamper built in Recommended for installation in an box ordered separately rather than a metal back for best performance Ships with 4 Panasonic CR123A 4 Duracell DL123A batteries SMB500 Optional surface mount backbox B210W Detector base used wireless detectors a built in magnet so that wireless devices can installed and tampered states FW PTOOL SWIFT Tools programming and diagnostic util Free download from notifier esd com For installation on typically laptop PC running an approved version of Win See Minimum System Requirements for SWIFT Requires the W USB radio antenna dongle for com with SWIFT Wireless devices 2 of 3 DN 60820 C 9 30 2015 SWIFT Tools is intended for use with NOTIFIER branded and can also be used with Fire branded wireless It will not work with other brands W USB Wireless USB radio antenna dongle that plugs into USB port of a PC running SWIFT Tools The W USB a communication link with SWIFT Wireless that are within approximately 20 feet and have not a mesh Alternately when the devices have formed mesh bringing the